ELTEX MES3108, Operation Manual, Page: 65 / 243

MES3000 Ethernet switch series 65
switchport general pvid
vlan_id
vlan_id
:
(1..4094)/1—if
default VLAN is defined,
otherwise—4095
Add port VLAN identifier (PVID) for the main interface.
no switchport general pvid Set the default value.
switchport general
ingress­filtering disable
-/filtering is enabled
Disable filtering of inbound packets on the main interface based
on their assigned VLAN ID.
no switchport general
ingress­filtering disable Enable filtering of inbound packets on the main interface based on
their assigned VLAN ID.
If filtering is enabled, and the packet is not in VLAN group with
assigned VLAN ID, this packet will be dropped.
switchport general
acceptable­frame-type
{tagged-only | untagged-only |
all}
-/accept all frame types
Accept only specific frame type on the main interface:
-
tagged-only —tagged only
- untagged-only —untagged only
- all —all frames
no switchport general
acceptable-frame-type Accept all frame types on the main interface.
switchport general map
protocols-group
group vlan
vlan_id
vlan_id
:
(1..4094);
group: (1..2147483647)
Set the classification rule for the main interface based on the
protocol tethering.
no switchport general map
protocols-group
group
Remove the classification rule.
switchport general map
macs­group
group vlan vlan_id
vlan_id: (1..4094);
group: (1..2147483647)
Set the classification rule for the main interface based on the MAC
address tethering.
no switchport general map
macs-group
group
Remove the classification rule.
switchport general map
subnets-group
group vlan
vlan_id
vlan_id: (1..4094);
group: (1..2147483647)
Set VLAN classification rule for an interface based on IP address
tethering.
no switchport general map
subnets-group
group
Remove the classification rule.
switchport dot1q ethertype
egress stag
ethertype
ethertype: ( 0..ffff)
(hex)
Replace EtherType in outbound packets from this interface .
Ethertype value should not match the reserved protocol
numbers or be less than the maximum value. General
reserved protocol numbers are listed in the Table 5.37.
no switchport dot1q ethertype
egress stag Set the default value.
switchport dot1q ethertype
ingress stag add
ethertype
ethertype: (0..ffff)
(hex)
Add EtherType to VLAN identifier table.
Ethertype value should not match the reserved protocol
numbers or be less than the maximum value. General
reserved protocol numbers are listed in the Table 5.37.
switchport dot1q ethertype
ingress stag remove
ethertype
Remove EtherType from VLAN identifier table.
switchport customer vlan
vlan_id
vlan_id
:
(1..4094)/1
Add VLAN for the user interface.
no switchport customer vlan Set the default value.
switchport customer
multicast-tv vlan
vlan_id
vlan_id
:
(1..4094)
Enable the multicast traffic receiving from the specified VLAN (that
is different from the user interface VLAN) on the configured
interface, together with other port users, that receive multicast
traffic from the current VLAN.
no switchport customer
multicast-tv vlan Disable the multicast traffic receiving for the configured interface.
switchport forbidden vlan add
vlan_list
vlan_list
:
(2..4094, all) /
all VLANs are enabled
for this port
Deny to add the selected VLANs for this port.
- vlan_list—list of VLAN IDs To define VLAN number range, enter
values separated by commas or separate starting and ending
values with a hyphen '-'.
switchport forbidden vlan
remove
vlan_list
Allow to add the selected VLANs for this port.
switchport forbidden
default­vlan
Membership in the
default VLAN is enabled
by default.
Deny to add the default VLAN for this port.
no switchport forbidden
default-vlan Set the default value.
switchport protected-port
-
Put the port in isolation mode within the port group.
no switchport-protected-port Restore the default value.