elsner elektronik Salva KNX basic Installation And Operation Manual Download Page 11

Page: 11 / 74

Installation and commissioning

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

Do not paint the smoke alarms!

Avoid the following sources of interference in order to limit distortion of measuring re-
sults for temperature, humidity and pressure:
•

Direct sunlight

•

Draughts from windows and doors

•

Warming or cooling of the building structure on which the sensor is mounted,
e.g. due to sunlight, heating or cold water pipes

•

Connection lines, which lead from warmer or colder areas to the sensor

Temperature variations from such sources of interference must be corrected in the ETS
in order to ensure the specified accuracy of the sensor (temperature offset).

2.3. Device design

2.3.1. Exterior view

Fig. 2
1

Skirting

Housing with electronics and battery

Openings for air circulation

Light transmission bar: Red LED for Operating and alarm signals

, page 17

and

Push-button for Function test, page 15

Summary of Contents for Salva KNX basic











































































Search results

Summary of Contents for Salva KNX basic

Reviews:

Related manuals for Salva KNX basic

Brands by name

Popular brands

elsner elektronik Salva KNX basic, Installation And Operation Manual

Search results

Summary of Contents for Salva KNX basic

Reviews:

Related manuals for Salva KNX basic

Brands by name

Popular brands