elsner elektronik Salva KNX basic Installation And Operation Manual Download Page 18

Page: 18 / 74

Device alarm functions

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

4.2.2. Serial number

The serial number on the type plate inside the device contains the production data and
device number:

Device alarm functions

5.1. Alarm mute (acknowledgement)

In this case, only the LED continues to flash every 10 seconds. After about 10 minutes,
the devices switches back to normal operating mode.

5.2. Alarm memory

An alarm is saved in the device for 24 hours. During this time, the LED briefly flashes
3 times every 43 seconds. The alarm memory can be reset by pressing the light trans-
mission bar (red LED) once.

5.3. Operating and alarm signals

Function / meaning

Signal tone

Red LED

Normal operating mode
(automatic self-test)

No sound

Flashes every 40 seconds

Alarm status

Loud interval tone in
0.5 second rhythm

Flashing twice per second

Fault / dirt

Short signal tone 3 times
every 40 seconds

LED off

Battery exchange display

1x Short signal tone
every 40 seconds

Flashes every 40 seconds
together with the signal
tone

Alarm mute (acknowledge-
ment)

No sound

Flashes every 10 seconds

Ser.no. 15111801

Year of production

-month

-day

Device number

Fig. 14

The alarm can be muted by pressing the
flashing light transmission bar.

Summary of Contents for Salva KNX basic











































































Search results

Summary of Contents for Salva KNX basic

Reviews:

Related manuals for Salva KNX basic

Brands by name

Popular brands

elsner elektronik Salva KNX basic, Installation And Operation Manual

Search results

Summary of Contents for Salva KNX basic

Reviews:

Related manuals for Salva KNX basic

Brands by name

Popular brands