elsner elektronik Salva KNX basic Installation And Operation Manual Download Page 35 | Manualshive

Page: 35 / 74

background image

34

Setting the parameters for all models

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

If the button acknowledgement is to be sent to the bus, set the function to "yes". Ac-
knowledgement is automatically switched off again 10 minutes after the end of the
smoke detection.

Then determine the value for the output object "smoke alarm: button acknowledge-
ment" in case of active acknowledgement and when it is to be sent.

External alarm

If an alarm message from another device to this device is also to trigger an alarm, then
set the function to "yes". Then determine the value for the alarm input object "smoke
alarm: external alarm" at which the external alarm should be active.

Sensor malfunction

If a sensor malfunction is to be sent to the bus, set the function to "yes".

Then determine the value for the output object "smoke alarm: malfunction" in the event
of a malfunction and when it is to be sent.

Battery warning

If a warning is to be issued when the battery is nearly flat, set the function to "yes".
A battery that is nearly flat is also always indicated locally on the device.

Use button acknowledgement

No • Yes

Object evaluation

1 = active • 0 = active

Send pattern

• on change
• on change to active
• on change to inactive
• on change and periodically
• on change to active and periodically
• on change to inactive and periodical

Cycle

(if sent periodically)

5 s • 10 s • 30 s • ... 2 h

Use external alarm

No • Yes

Object evaluation

1 = active • 0 = active

Use malfunction object

No • Yes

Object evaluation

1 = active • 0 = active

Send pattern

• on change
• on change to active
• on change to inactive
• on change and periodically
• on change to active and periodically
• on change to inactive and periodical

Cycle

(if sent periodically)

5 s • 10 s • 30 s • ... 2 h

Use battery warning

No • Yes

«
...
33
34
35
36
37
...
»

Summary of Contents for Salva KNX basic











































































Reviews:

No comments

Related manuals for Salva KNX basic

RADIO CONTROLLED PROJECTION ALARM CLOCK

Brand: La Crosse Technology Pages: 25

Brand: Masterbuilt Pages: 52

Megalarm MEGA 2400

Brand: MEGATRONIX Pages: 24

Brand: Viper Pages: 45

Brand: Prestige Pages: 8

Brand: Vanderbilt Pages: 5

Brand: Konyks Pages: 8

Brand: EVERSPRING Pages: 13

nightvision 21103

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 3

Brand: Equity Pages: 2

Brand: iHome290 Pages: 13

Brand: Navox Pages: 12

Brand: Navox Pages: 22

Brand: BALANCE TIME Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands