elsner elektronik Salva KNX basic Installation And Operation Manual Download Page 69 | Manualshive

Page: 69 / 74

background image

68

Temperature and humidity parameters

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

urgently and needs longer until the necessary control variable for the setpoint value
deviation is reached.
You should set the time appropriate for the humidification/dehumidification system at
this point (note manufacturer instructions).

Now specify, what should be sent when the control is blocked.
On release, the control variable follows the rule again.

8.8.

Dewpoint measurement

The

Smoke alarm Salva KNX

calculates the dewpoint temperature and can output

the value to the bus.

Activate the monitoring of the coolant temperature if required. The menus for setting
the monitoring are displayed.

8.8.1. Cooling medium temp. monitoring

A threshold value can be set for the temperature of the coolant, which is based on the
current dewpoint temperature (offset/deviation). The switching output of the coolant
temperature monitoring system can provide a warning prior to any build-up of conden-
sation in the system, and/or activate appropriate countermeasures.

Threshold value

Threshold value = dewpoint tempe offset

Set, in which cases

offset

received via object is to be retained. Please note that the set-

ting "After power supply restoration and programming" should not be used for the in-

Maximum control variable is reached
at target/actual difference of %

1...50; 5

Reset time in minutes

1...255; 3

When blocked, the control variable shall

• not be sent
• send a specific value

Value in %
(

if a value is sent)

0...100

Sending pattern

• never
• periodically
• on change
• on change and periodically

At and above change of

(if sent on change)

0.1°C • 0.2°C • 0.5°C • 1.0°C • 2.0°C • 5.0°C

Send cycle

(if sent periodically)

5 s • 10 s • 30 s • 1 min • … • 2 h

Use monitoring of the coolant temperature

No • Yes

«
...
67
68
69
70
71
...
»

Summary of Contents for Salva KNX basic











































































Reviews:

No comments

Related manuals for Salva KNX basic

Brand: Tyco Electronics Pages: 100

Brand: FIBARO Pages: 14

Brand: LST Pages: 1

Brand: Sonic Alert Pages: 5

TRUSENSE SMOKE 2050-DS10

Brand: Kidde Pages: 28

Brand: Geemarc Pages: 32

Brand: Trust Pages: 77

Brand: CrimeStopper Pages: 26

Brand: IKEA Pages: 120

CoolStart RS-1604TW1

Brand: CrimeStopper Pages: 28

Filtrex FTX-P1A

Brand: System Sensor Pages: 4

Brand: Guardian Pages: 10

Brand: Code Alarm Pages: 16

Brand: Hyundai Pages: 20

Brand: Hamrforge Pages: 9

Brand: Davita Pages: 66

Brand: Fox Pages: 13

Brand: UniPOS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands