elsner elektronik Salva KNX basic Installation And Operation Manual Download Page 9 | Manualshive

Page: 9 / 74

background image

8

Installation and commissioning

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

The device is only to be used for its intended purpose. Any improper modification or
failure to follow the operating instructions voids any and all warranty and guarantee
claims.

After unpacking the device, check it immediately for possible mechanical damage. If it
has been damaged in transport, inform the supplier immediately.

The device may only be used as a fixed-site installation; that means only when assem-
bled and after conclusion of all installation and operational start-up tasks and only in
the surroundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur
after publication of these operating instructions.

2.2. Installation location

2.2.1. Equipping the building with smoke alarms

The minimum protection is the installation of smoke alarms in the bedrooms and halls
and/or corridors to ensure that you are woken up during the night in case of a smoke
alarm. If the building has several floors, at least one smoke alarm should be installed
in the hall on every floor. Please refer to DIN 14676 for further installation guidelines.

2.2.2. Positioning and distances

Install the smoke alarm on the room ceiling. If the smoke alarm is installed in the mid-
dle of the room, it has its best detection characteristics.

WARNING!
Mains voltage for in-wall concealed cables!

•

If the device is attached by means of screws, first ensure
that there is no power line installed under the assembly point!

Fig. 1

Minimum equipment

Ideal equipment

Equipment with limitations

Maintain a minimum distance of 50 cm to:
•

walls

•

lamps

•

live wires

≥

50 cm

«
...
7
8
9
10
11
...
»

Summary of Contents for Salva KNX basic











































































Reviews:

No comments

Related manuals for Salva KNX basic

Brand: La Crosse Technology Pages: 6

Brand: La Crosse Technology Pages: 7

Brand: Daffodil Pages: 3

Brand: Scott Pages: 2

Brand: ThermoWorks Pages: 2

Brand: Clifford Pages: 28

Brand: Cablematic Pages: 10

NUBI 4.0 NB40LP1

Brand: Smartek Pages: 4

Brand: Asante Pages: 2

Brand: SkyScan Pages: 7

Fire-Lite SD350

Brand: Pittway Pages: 2

Brand: LEM Pages: 6

Brand: GE Pages: 10

Brand: GE Pages: 4

Brand: Trevi Pages: 6

Brand: Trevi Pages: 8

Brand: MiniMax Pages: 10

Brand: Prestige Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands