Element4 Bidore 140, User And Installation Manual

Page: 6 / 48

6
USER INFORMATION
MAN position
By briefly pressing the SET button, you will go
through the following functions:
MAN →
✹
TEMP → TEMP → (P*)TIMER →
MAN
where, depending on the timer setting:
(P*) is displayed as P1 , , P1 , P2
✹
,
P2 .
You can also go back to the MAN position by
pressing the button
or
!Caution - When pressing the buttons (with the
exception of the SET button), the transmission
symbol (
) will appear to indicate that
transmission is taking place between the remote
control and the receiver;
- The receiver acknowledges the transmission
with a sound signal;
- The appliance will automatically enter the
standby position, if there is no transmission for
6 hours.
Set the remote control to the MAN position.
Ignition
Caution - During the ignition process, you are
not allowed to operate control button B
on the gas control manually
- Always wait 5 minutes after the pilot burner
has gone out, before you re-ignite
the appliance;
I g n i t e t h e a p p l i a n c e a s f o l l o w s ;
Simultaneously press the buttons and
on the remote control.
Let go of the buttons when a short sound signal in-
dicates that the ignition process has been started.
In succession:
- the continuous signals will indicate that the igni-
tion process is active;
- a short sound signal will indicate that the ignition
process has finished;
- the appliance will automatically switch through
to the highest position of the main burner, which
will start to burn in a few seconds.
Caution - If the pilot burner is not burning after
3 ignition attempts, you must close the gas
tap and call the installer;
- When igniting the pilot burner, you will hear
sound signals. After the last short sound sig-
nal, the main burner should be largely ignited
within about 10 seconds. If this is not the
case, you must close the gas tap and warn
your installer;
- If the appliance ignites with a pop sound, you
must close the gas tap and
contact your installer.
!Tip A little motor will start to run when the
main burner operates, you will be able to hear
it.
✹
6
USER INFORMATION
MAN position
By briefly pressing the SET button, you will go
through the following functions:
MAN → TEMP → TEMP → (P*)TIMER
→ MAN
where, depending on the timer setting:
(P*) is displayed as P1 , , P1 , P2 ,
P2 .
You can also go back to the MAN position by
pressing the button
or
!Caution - When pressing the buttons
(with the exception of the SET button), the
transmission symbol ( ) will appear to
indicate that transmission is taking place
between the remote control and the receiver;
- The receiver acknowledges the transmission
with a sound signal;
- The appliance will automatically enter the
standby position, if there is no transmission
for 6 hours.
Set the remote control to the MAN position .
Ignition
Caution - During the ignition process, you
are not allowed to operate control button B
on the gas control manually
- Always wait 5 minutes after the pilot burner
has gone out, before you re-ignite
the appliance;
3
I g n i t e t h e a p p l i a n c e a s f o l l o w s ;
Simultaneously press the buttons and
on the remote control.
Let go of the buttons when a short sound signal
indicates that the ignition process has been
started.
In succession:
- the continuous signals will indicate that the ignition
process is active;
- a short sound signal will indicate that the ignition
process has finished;
- the appliance will automatically switch through to
the highest position of the main burner, which will
start to burn in a few seconds.
Caution - If the pilot burner is not burning after
3 ignition attempts, you must close the gas tap
and call the installer;
- When igniting the pilot burner, you will hear
sound signals. After the last short sound signal,
the main burner should be largely ignited within
about 10 seconds. If this is not the case, you
must close the gas tap and warn your installer;
- If the appliance ignites with a pop sound, you
must close the gas tap and
contact your installer.
!Tip A little motor will start to run when the main
burner operates, you will be able to hear it.
B
A
6
USER INFORMATION
MAN position
By briefly pressing the SET button, you will go
through the following functions:
MAN → TEMP → TEMP → (P*)TIMER
→ MAN
where, depending on the timer setting:
(P*) is displayed as P1 , , P1 , P2 ,
P2 .
You can also go back to the MAN position by
pressing the button
or
!Caution - When pressing the buttons
(with the exception of the SET button), the
transmission symbol ( ) will appear to
indicate that transmission is taking place
between the remote control and the receiver;
- The receiver acknowledges the transmission
with a sound signal;
- The appliance will automatically enter the
standby position, if there is no transmission
for 6 hours.
Set the remote control to the MAN position .
Ignition
Caution - During the ignition process, you
are not allowed to operate control button B
on the gas control manually
- Always wait 5 minutes after the pilot burner
has gone out, before you re-ignite
the appliance;
3
I g n i t e t h e a p p l i a n c e a s f o l l o w s ;
Simultaneously press the buttons and
on the remote control.
Let go of the buttons when a short sound signal
indicates that the ignition process has been
started.
In succession:
- the continuous signals will indicate that the ignition
process is active;
- a short sound signal will indicate that the ignition
process has finished;
- the appliance will automatically switch through to
the highest position of the main burner, which will
start to burn in a few seconds.
Caution - If the pilot burner is not burning after
3 ignition attempts, you must close the gas tap
and call the installer;
- When igniting the pilot burner, you will hear
sound signals. After the last short sound signal,
the main burner should be largely ignited within
about 10 seconds. If this is not the case, you
must close the gas tap and warn your installer;
- If the appliance ignites with a pop sound, you
must close the gas tap and
contact your installer.
!Tip A little motor will start to run when the main
burner operates, you will be able to hear it.
B
A