Stellar Hearth 4-SS-2-GL Installation And Operating Manual Download Page 1

Page: 1 / 37

Custom Fireplace Program

Co-linear Direct Vent

Gas Fireplaces

GALAXY SERIES - SINGLE SIDED
Installation and Operating Manual
NG & LP

Installer:

Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

— Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other

appliance.

—

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•

If you cannot reach your gas supplier, call the ﬁ re department.

— Installation and service must be performed by a qualiﬁ ed installer, service agency or the gas supplier.

WARNING: If the information in these instructions are not followed exactly, a ﬁ re or explosion may result
causing property damage, personal injury or loss of life.

www.stellarhearth.com

Stellar Hearth Products

, a division of Hearth & Home Technologies

- 16873 Fish Point Rd SE, Prior Lake, MN 55372 - (952) 224 - 4072

Page 1

Summary of Contents for 4-SS-2-GL






































Search results

Summary of Contents for 4-SS-2-GL

Reviews:

Related manuals for 4-SS-2-GL

Brands by name

Popular brands

Stellar Hearth 4-SS-2-GL, Installation And Operating Manual

Search results

Summary of Contents for 4-SS-2-GL

Reviews:

Related manuals for 4-SS-2-GL

Brands by name

Popular brands