Electrovision NJ174 COTO CIRC User Manual Download

Page: 12 / 12

SERVICE WARRANTY

NJD guarantees the product free from defects in

materials and workmanship for a period of one year.

Should this luminaire be operated under conditions other

than those recommended, at voltages other than the

voltage indicated on the luminaire, or any attempts made

to service or modify the luminaire, then the warranty will

be rendered void.

The product you buy may sometimes differ slightly from

illustrations. This warranty is in addition to, and does not

affect, your statutory rights.

If you have any problems with this product, please call

our Help Desk on (0845) 459 4816. The help desk is

open from 8 am until 1 pm, Monday to Friday.

Electrovision Ltd.,

Lancots Lane,

Sutton Oak,

St. Helens,

Merseyside.

WA9 3EX

website:

www.electrovision.co.uk

Page 12

Summary of Contents for NJ174 COTO CIRC













Search results

Summary of Contents for NJ174 COTO CIRC

Reviews:

Related manuals for NJ174 COTO CIRC

Brands by name

Popular brands

Electrovision NJ174 COTO CIRC, User Manual

Search results

Summary of Contents for NJ174 COTO CIRC

Reviews:

Related manuals for NJ174 COTO CIRC

Brands by name

Popular brands