background image

PRODUCT SAFETY

 This luminaire is for professional use only.  It is the

owner's responsibility to ensure that all users are given

adequate supervision and instruction concerning the use

of the appliance in a safe way and understand the

hazards involved.

 Children should be supervised to ensure that they do

not play with the luminaire.

 Do not stare into the beam.

 Do not place on carpet or other soft surfaces.

 For indoor use only.

 Do not use in bathrooms, or in wet or damp locations.

 Do not place the mains lead beneath a carpet or rug.

 Do not allow the cable to hang over the edge of a table.

 Arrange the cable so that it cannot cause a trip

hazard.

This symbol means that the luminaire should

mounted at least 0.3 m from any object that

it is illuminating.

0.3m

GENERAL SAFETY

REQUIREMENTS

Domestic wiring must be tested periodically by a qualified

electrician at least once every 10 years or at every

change of occupancy.

For office and retail premises, and buildings such as

village halls, the wiring must be inspected at least once

every 5 years.

It is recommended that all building be fitted with smoke

alarms (it is mandatory for new buildings). Ionisation-type

smoke alarms are recommended for buildings where

theatrical fog effects are to be used.

 Page 3

Summary of Contents for NJ174 COTO CIRC













Reviews: