Electrolux EXH09HL1W Service Manual Download Page 19

Page: 19 / 62

210-10 ADL

19/62

599 75 60-77

(3) Heating M

ode (this mode isn’t available for cooling only unit)

①

Heating Conditions and Process

When Tamb. ≤2

℃

, the unit operates in cooling mode. Compressor and outdoor fan operate and indoor fan operates

according to cold air prevention.

When Tamb.≥5

℃

, compressor and outdoor fan stop operation, while indoor fan operates according to blowing residual

heat.

When 2

℃

＜

Tamb.

＜

℃

, the unit operate at previous running status.

In heating mode, the temperature setting range is 16

～

℃

; Indoor unit displays operation icon, cooling icon and set

temperature.

②

Defrosting

When there’s too much frost on outdoor condenser, the complete unit will enter into defrosting automatically to assure the best

heating effect. During defrosting process, H1 is displayed.

③

Blow Residual Heat

When heating temperature reaches to the temperature point of stop operation, compressor and outdoor fan will stop operation.

The big horizontal louver rotates to the defaulted position in cooling and small horizontal louver will close. Indoor fan will stop

operation after operating at set fan speed for 60s.

When the unit operates in heating or auto heating mode, compressor is started up and the unit will stop operation after indoor

fan starts operation. Compressor and outdoor fan stop operation. The big horizontal louver will rotate to the position of breeze

(defaulted position in cooling), while the small horizontal louver will close. The unit will stop operation after indoor fan operates

at low fan speed for 10s.

④

Cold Air Prevention

In heating mode, in order to prevent the cold air comes out when turning on the compressor, the indoor fan can only be started

up after compressor operates for 2 minutes.

Summary of Contents for EXH09HL1W































































Search results

Summary of Contents for EXH09HL1W

Reviews:

Related manuals for EXH09HL1W

Brands by name

Popular brands

Electrolux EXH09HL1W, Service Manual

Search results

Summary of Contents for EXH09HL1W

Reviews:

Related manuals for EXH09HL1W

Brands by name

Popular brands