manualshive.com logo in svg

Electrolux Built-In Dishwasher, Service Manual

Share
Download
Electrolux Built-In Dishwasher Service Manual Download Page 51

51

5995432258

9. Place the fresh food shelf in the top position. Place the
    evaporator assembly on the shelf.

Caution: 

Refrigerant lines may be damaged if the

evaporator assembly is left unsupported.

Fresh Food Evaporator Fan Assembly

To remove the fresh food evaporator fan
assembly:

1. Access the fresh food evaporator assembly.
    (

See Fresh Food Evaporator Assembly

).

2. The fan assembly is attached to the evaporator
    assembly with 4 Phillips-head screws (2 on each side
     of the fan assembly). Remove the 4 screws that hold
     the fan assembly in place.

3. Separate the fan assembly from the evaporator
   assembly.

Fresh Food Evaporator

To access the fresh food evaporator:

1. Access the fresh food evaporator assembly.
(

See Fresh Food Evaporator Assembly.

)

2. Remove the fresh food evaporator fan assembly. (See

    Fresh Food Evaporator Fan Assembly.

)

3. Remove the tape from the front of the Styrofoam cover.
     Note the position of the wires under the tape. The tape
    must be replaced after repair.
4. Remove the Styrofoam cover.

WARNING: 

The evaporator fi ns are very sharp. Wear

Kevlar gloves when handling.

5. Remove the 2 Phillips-head screws that hold the fresh
   food evaporator in place (Fig. 1 and Fig. 2)

6. Disconnect the 2 electrical connectors and lift the fresh
   food evaporator from the housing.

WARNING: 

The evaporator fi ns are very sharp. Wear

Kevlar gloves when handling.

Summary of Contents for Built-In Dishwasher


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands