manualshive.com logo in svg

Electrolux Built-In Dishwasher, Service Manual

Share
Download
Electrolux Built-In Dishwasher Service Manual Download Page 47

47

5995432258

    the freezer evaporator cover.
4. Remove the 2 Phillips-head screws that hold the rear
    air duct cover in place, then pull it down.

5. Disconnect all the electrical connectors from the
   ceiling.
6. Remove the rear air duct cover.
7. Remove the 2 Phillips-head screws from the suction
    line drain pan and heater assembly. Disconnect the
    associated wiring.

Note: 

The suction line drain pan heater has a resistance

value of 1.3K  Ohm.

8. Carefully remove the styrofoam air duct.

Note: 

The styrofoam air duct is held in place by adhesive.

9. Remove the 2 Phillips-head screws that hold the freezer
    plug cover in place, then remove the freezer plug cover.
   Freezer Plug Cover

10. Disconnect the freezer evaporator wiring.

Note: 

When installing plug cover, place wiring

connectors inside the cover, then mount the plug
cover to the wall.

11. Remove the 2 Phillips-head screws that hold the

Summary of Contents for Built-In Dishwasher


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands