manualshive.com logo in svg

Electrolux Built-In Dishwasher, Service Manual

Share
Download
Electrolux Built-In Dishwasher Service Manual Download Page 36

36

5995432258

# WR02X10471.

Approximate water temperature by the glass:

• Room Ambient at 76°F (24°C).
• 8-ounce glass.
• One-minute interval between dispensing water.

Duct Door Assembly

Duct Door

The dispenser control panel must be removed before
removing the duct door.

Insert a fl at-blade screwdriver between the duct door (top
right corner) and the switch housing. Use the screwdriver
to slide the door to the left, until the hinge pin is free.

Duct Door Motor Switch Housing

The dispenser motor operates through 2
switches located in a housing at the top, right
corner of the dispenser cavity. The dispenser
motor switch housing is held in place by 4

Phillips-head screws.

The duct door motor switches are held in place by

2 tabs.

Duct Door Motor

The duct door motor rotates an eccentrically
shaped plastic cam which operates the duct door.

Summary of Contents for Built-In Dishwasher


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands