Electrolux Professional 603877, Installation And Operating Manual, Page: 14 / 46

14
Electrolux Professional strongly recommends using Electrolux
Professional approved cleaning, rinse and descaling agents to
obtain optimal results and maintain product efficiency over
time.
The Electrolux Professional warranty does not cover:
• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless
resulting from defects in materials or workmanship reported
within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages,
failures and inefficiencies caused by and/or resulting from;
– insufficient and/or abnormal capacity of the electrical
systems (current/voltage/frequency, including spikes and/or
outages);
– inadequate or interrupted water supply, steam, air, gas
(including impurities and/or other that does not comply with
the technical requirements for each appliance);
– plumbing parts, components or consumable cleaning
products that are not approved by the manufacturer;
– customer’s negligence, misuse, abuse and/or non-com-
pliance with the use and care instructions detailed within the
appropriate equipment documentation;
– improper or poor: installation, repair, maintenance
(including tampering, modifications and repairs carried out
by third parties not authorized) and modification of safety
systems;
– Use of non-original components (e. g.: consumables,
wear and tear, or spare parts);
– environment conditions provoking thermal (e. g. over-
heating/freezing) or chemical (e. g. corrosion/oxidation)
stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents,
chips, and/or other damage to the finish of the product,
unless such damage results from defects in materials or
workmanship and is reported within one (1) week of delivery
unless otherwise agreed;
• product with original serial numbers that have been
removed, altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by
Electrolux Professional.
Warranty does not include scheduled maintenance activities
(including the parts required for it) or the supply of cleaning
agents unless specifically covered within any local agreement,
subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized
customer care.
C GENERAL SAFETY RULES
WARNING
Refer to “ Warning and safety
information “.
C.1 Protection devices installed on the
appliance
Guards
The appliance has:
• fixed guards (e.g. casings, covers, side panels, etc.), fixed
to the appliance and/or frame with screws or quick-release
connectors that can only be removed or opened with tools;
therefore the user must not remove or tamper with such
devices. The Manufacturer declines any liability for damage
due to tampering or their non-use;
• interlocked movable guards (door) for access inside the
appliance;
• appliance electrical equipment access panels or doors,
made from hinged panels openable with tools. The panel
or the door must not be opened when the appliance is
connected to the power supply.
C.2 Safety signs to be placed on the
appliance or near its area
Prohibition Meaning
do not remove the safety devices
do not use water to extinguish fires
(placed on electrical parts)
Danger Meaning
danger of crushing hands
caution hot surface
danger of electrocution (shown on elec-
trical parts with indication of voltage)
C.3 End of use
When the appliance is no longer to be used, make it unusable
by removing the mains power supply wiring.
C.4 Precautions for use and maintenance
• Risks mainly of a mechanical, thermal and electrical nature
exist in the appliance. Where possible the risks have been
neutralised:
– directly, by means of adequate design solutions.
– indirectly by using guards, protection and safety devices.
• Any anomalous situations are signalled on the control panel
display.
• During maintenance several risks remain, as these could
not be eliminated, and must be neutralised by adopting
specific measures and precautions.
• Do not carry out any checking, cleaning, repair or main-
tenance operations on moving parts. Workers must be
informed of this prohibition by means of clearly visible signs.
• Make sure to periodically check correct operation of all the
safety devices and the insulation of electrical cables, which
must be replaced if damaged.
In case of a significant anomaly (e. g. short circuits, wires
coming out of the terminal block, motor breakdowns, worn