ELECTRO FREEZE SLX400 Operator'S Manual With Replacement Parts List Download Page 7

Page: 7 / 70

ELECTRO FREEZE Soft Serve Models SLX400, SLX400E, SLX500

Table of Contents

Safety First!

............................................................................................... ii

Safety Decal Locations

................................................................... iv

PART I

Introduction

............................................................................................... 1

Note to Installer

...................................................................................... 1

2.1 Uncrating and Inspection ............................................................................... 2

2.2 Installation ..................................................................................................... 3

2.3 Electrical Requirements - Models SLX500 and SLX400 ................................. 3

2.4 Electrical Requirements - Model SLX400E .................................................... 4

2.5 Electrical Connections ................................................................................... 4

Specifications

.......................................................................................... 5

3.1 Particulars. ...................................................................................................... 5

3.2 Data Plate ....................................................................................................... 6

3.3 Reference Information .................................................................................... 6

3.4 Installation Date .............................................................................................. 7

3.5 Dimensions. .................................................................................................... 7

Virtual Quality Management System (VQM)
Terminology

.............................................................................................. 8

Part Names and Functions

........................................................ 10

Operator Controls & Indicators

.............................................. 13

6.1 Freezer Symbol .......................................................................................... 14

6.2 Left Side Controls ....................................................................................... 14

6.3 Indicates Mode of Operation ...................................................................... 14

6.4 OFF Indicator .............................................................................................. 14

6.5 Functions buttons (Four) ............................................................................. 14

6.6 Information Window ................................................................................... 14

6.7 Wash or Clean Mode .................................................................................. 14

6.8 Night Mode Button ...................................................................................... 15

6.9 Freeze Mode Button ................................................................................... 15

6.10 OFF Button .................................................................................................. 15

6.11 Left Side Beater "ON" Button ...................................................................... 15

Summary of Contents for SLX400







































































Search results

Summary of Contents for SLX400

Reviews:

Brands by name

Popular brands

ELECTRO FREEZE SLX400, Operator'S Manual With Replacement Parts List

Search results

Summary of Contents for SLX400

Reviews:

Brands by name

Popular brands