manualshive.com logo in svg

ELECTRO FREEZE SLX400, Operator'S Manual With Replacement Parts List

Share
Download
ELECTRO FREEZE SLX400 Operator'S Manual With Replacement Parts List Download Page 23

ELECTRO FREEZE Soft Serve Models SLX400, SLX400E, SLX500

184584

      

   15

Figure 6-1

6.8

Function Buttons (Four)    8

Press the function button directly below icon to activate the “Night” mode of operation.

6.9

Freeze Mode Button     9

Press

 

 

button will activate the automatic freeze mode and return display to main screen.

6.10

Off  Button     10

Press OFF button to return to main screen display and turn left side of the freezer off.

6.11

Left Side Beater “ON”  Button    11

Pressing this button to turn left side beater ON

6.12

Left Side Beater “OFF”  Button    12

 Press this button to turn left side beater OFF

6.13

Arrow Buttons   13

Used by technicians for programming an setting changes.  See Troubleshooting

section for Operator accessible controls.

Press to enter
Operator Mode
(Hidden button)

Summary of Contents for SLX400







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands