Electra Honeycomb Series How To Install Download Page 6

Page: 6 / 18

Honeycomb Blind Installation Face-fix

(outside recess)

STEP 1- Spacing

Mark the brackets approx
3.5cm in from each end
with the other brackets
spaced evenly between
them. Be careful to avoid

any obstructions/window
handles as the blind may
be damaged if it is
lowered onto these.

STEP 3- Fit mounting
clip
Fit the mounting clip
on to the bracket with
the larger lip to the
front.

STEP 2- Fitting the brackets Secure
the brackets in place at the marks
previously made using suitable
fixings.

STEP 4- Mounting the

Honeycomb blind

Place the back lip of your

headrail into the back

hook of the bracket and

push into the mounting

clip until there is a firm

'click'.

Electra Top Tip!
If securing the brackets to
plaster, stone, brick, etc.,
drill the holes at the
marked positions using a
5.5mm masonry drill bit,
then use the wall plugs
and screws supplied to fix
the brackets.

Summary of Contents for Honeycomb Series



















Search results

Summary of Contents for Honeycomb Series

Reviews:

Related manuals for Honeycomb Series

Brands by name

Popular brands

Electra Honeycomb Series, How To Install

Search results

Summary of Contents for Honeycomb Series

Reviews:

Related manuals for Honeycomb Series

Brands by name

Popular brands