EKKO ES100E Operator'S And Service Manual Download Page 10

Page: 10 / 65

Personal Safety Work Area Safety

Personal Fall Protection

Personal fall protection equipment (PFPE) is

not required when operating this machine. If

PFPE is required by job site or employer

rules, the following shall apply:

All PFPE must comply with applicable

governmental regulations and must be

inspected and used in accordance with the

man

ufacturer’s instructions.

Electrocution Hazards

This machine is not electrically insulated and

will not provide protection from contact with or

proximity to electrical current.

Obey all local and governmental regulations

regarding required clearance from electrical

power lines. At a minimum, the required

clearance contained in the chart below must

be followed.

Line Voltage

Required Clearance

0 to 300V

Don’t touch

300V to 50KV

120 Inch

50KV to 200KV

181 Inch

200KV to 350KV

240 Inch

350KV to 500KV

300 Inch

500KV to 750KV

420 Inch

750KV to 1000KV

540 Inch

Allow for platform movement, electrical line

sway or sag, and beware of strong or gusty

winds.

Keep away from the machine if it contacts

energized power lines. Personnel on the

ground or in the platform must not touch or

operate the machine until energized power

lines are shut off.

Do not operate the machine during lightning or

storms.

Do not use the machine as a ground for

welding

Summary of Contents for ES100E


































































Search results

Summary of Contents for ES100E

Reviews:

Related manuals for ES100E

Brands by name

Popular brands

EKKO ES100E, Operator'S And Service Manual

Search results

Summary of Contents for ES100E

Reviews:

Related manuals for ES100E

Brands by name

Popular brands