eka KF 630 D UD, Use And Instruction Manual

Page: 8 / 19

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page. 8 ________________________________________________________________________________________
5) Fix the pump (1) to the frame with the appropriate support (2) and the two screws (4)
included.
6) Connect the cables previously disconnected from electrovalve to pump.
7) Connect the tube previously disconnected from electrovalve to pump’s linking.
8) Connect the tube (6) with filter and ballast (included in “Pump kit”) to pump’s apron (7).
9) Replace back cover.
Fig.1
Fig.1 Fig.1
Fig.1
Warning: Warning: Warning: Warning:
To avoid limestone buildup into the cooking chamber, we suggest to fill the water tank with
decalcified water.
Check water level in the tank before activating the pump and during its functioning. If pump Check water level in the tank before activating the pump and during its functioning. If pump Check water level in the tank before activating the pump and during its functioning. If pump Check water level in the tank before activating the pump and during its functioning. If pump
works without water in the tank, what occurs is ab
works without water in the tank, what occurs is ab works without water in the tank, what occurs is ab
works without water in the tank, what occurs is abnormal noise at first and then its breakage
normal noise at first and then its breakage normal noise at first and then its breakage
normal noise at first and then its breakage
....
Connecting the power cable
Connecting the power cable Connecting the power cable
Connecting the power cable::::
– –– –
Mod.
Mod. Mod.
Mod. KF 6
KF 6 KF 6
KF 63
3 3
30 D
0 D 0 D
0 D UD
UD UD
UD
– –– – The terminal board is on the rear panel of the appliance. Open the
terminal board cover by obtaining leverage with a screwdriver on the two side fins. Loosen the
cable gripper screw and allow the cable to pass through it. Arrange the conductors so that the
earth conductor is the last to detach from its terminal if the cable goes into a state of faulty
traction. Connect the phase
phase phase
phase conductor to the terminal marked with the letter "L"
"L" "L"
"L", the neutral
neutral neutral
neutral
conductor to the terminal marked with the letter "N"
"N" "N"
"N" and the earth
earth earth
earth conductor to the terminal
marked with the symbol .
Tighten the ring-nut of the cable gripper and close the terminal board cover.
– –– –
Modd. Modd. Modd. Modd. KF 733 D UD KF 733 D UD KF 733 D UD KF 733 D UD –––– KF KF KF KF 9 9 9 937 37 37 37 D D D D UD UD UD UD
– –– – To access the terminal board, just remove the
appliance's rear side-panel. Loosen the cable gripper and allow the cable to pass through it.
Arrange the conductors so that the earth conductor is the last to detach from its terminal if the
cable goes into a state of faulty traction. Connect the phase
phase phase phase conductor to the terminal marked
“L1” “L1” “L1” “L1”, connecting the neutral neutral neutral neutral conductor to the terminal marked "N" "N" "N" "N" and the earth earth earth earth conductor to
the terminal marked with the symbol
.
Tighten the cable gripper and re-fit the rear side-panel of the appliance.
–
Mod
Mod Mod
Modd
d d
d.
. .
. KF 966 D AL
KF 966 D AL KF 966 D AL
KF 966 D AL UD
UD UD
UD –––– KF 966 D UD
KF 966 D UD KF 966 D UD
KF 966 D UD
– –– – To access the terminal board, just remove the
appliance's rear side-panel. Loosen the cable gripper and allow the cable to pass through it.
Arrange the conductors so that the earth conductor is the last to detach from its terminal if the
cable goes into a state of faulty traction. Connect the phase
phase phase
phase conductors to the terminals marked
“L1”
“L1” “L1”
“L1” and “L2”
“L2” “L2”
“L2”, connecting the neutral
neutral neutral
neutral conductor to the terminal marked "N"
"N" "N"
"N" and the earth
earth earth
earth
conductor to the terminal marked with the symbol
according to the following lay-out: