EINHELL BT-LS 810 D, Operating Instructions Manual

Page: 13 / 276

Packaging
The device is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
When using the equipment, a few safety
precautions must be observed to avoid injuries
and damage.
Read the operating instructions carefully and
comply with them. It is important to consult these
instructions in order to acquaint yourself with the
unit, its proper use and safety regulations.
Keep this manual in a safe place, so that the
information is available at all times.
If you give the equipment to any other person,
hand over these operating instructions as well.
We cannot accept any liability for damage or
accidents which arise due to a failure to follow
these instructions.
1. Scope of use
The wood splitter is designed for splitting wood with
maximum lengths of 520/780/1040 mm and a
maximum diameter of 320 mm. Please note that our
equipment has not been designed for use in
commercial, trade or industrial applications. Our
warranty will be voided if the equipment is used in
commercial, trade or industrial businesses or for
equivalent purposes.
2. Safety instructions and symbols
used
The applicable safety instructions and explanations
of the symbols on the device are set out in the
enclosed booklet.
3. Layout and items supplied (Fig. 1-2)
1. Splitter
2. Trunk
support
3. Hand guards
4. Control lever
5. Trunk support holder
6. Supporting
foot
7. Wheels
8. Switch/plug
combination
9. Motor
10. Transport handle
11. Trunk holding plates
12. Star nut for adjusting the splitter height
13. Fastening set for trunk holding plates
14. Oil filler/gauge screw
4. Assembly
4.1. Fitting the control lever and hand guards
(Fig. 3-6)
Remove the securing splint pins (Fig. 3/Item 15),
bolts (Fig. 4/Item 16) and washers (Fig. 4/Item 17)
from the holders. Push the hand guards and control
lever, as shown in Figure 5, from the front into the
mount so that the ends of the control lever (Fig.
5/Item A) project through the recesses provided for it
in the control rod (Fig. 5/Item B) (Fig. 5). Fasten the
hand guards with the bolts which you previously
removed (Fig. 5/Item 16). The washers (Fig. 5/Item
17) provide a point of support and should be placed
between the hand guard and the base plate as shown
in Fig. 5. Then secure the bolts with the securing
splint pins (Fig. 6/Item 15).
4.2. Fitting the trunk holding plates (Fig. 7-8)
Push the trunk holding plates (Fig. 2/Item 11) through
the guide slots in the hand guards, as shown in Figure
7. As you do this, ensure that the oval holes in the
trunk holding plates line up with the securing holes in
the hand guards. Secure them with the fastening set
(Fig. 2/Item 13) as shown in Fig. 8. The trunk holding
plates can now be adjusted to the trunk thickness
using the oval holes.
4.3 Fitting the trunk support (Fig. 9-10)
The trunk support can be installed at three different
heights (Fig. 2):
Position A: Max. log length 520 mm
Position B: Max. log length 780 mm
Position C: Max. log length 1040 mm
There are three attachment devices at different
heights on the wood splitter for this purpose. To use
the trunk support, the locking levers on the
appropriate attachment device must be moved
upwards (Fig. 9) so that they are vertical (Fig. 24).
The trunk support must then be pushed into the
attachment device from the front and secured by
returning the locking levers to their original positions
(Fig. 10).
In addition, you can also limit the lifting height of the
splitter. To do so, turn the machine off and slacken
the star screw (Fig. 12/Item 12) by 2-3 turns, then
raise the limit bar to the required height and affix in
position by tightening the star screw (Fig. 12/Item 12).
13
GB
Anleitung_BT_LS_810_D_SPK7:_ 05.09.2007 12:58 Uhr Seite 13