EFKA AB60D1472
60
6.2 Operator
Level
The preset values of the following list of parameters refer to the setting of parameter 290 = 0.
Parameter
Designation
Unit
max
min
Preset
Ind.
000
c2 - Stitch counting
stitches
254
0
2 *)
A
- End counting limited speed until stop
001
c1 - Stitch counting
stitches
254
0
2 *)
A
- Start counting limited speed n3
002
c3 - Stitch counting
stitches
254
0
2 *)
A
- Counting tape cutter at the start of the seam
003
c4 - Stitch counting
stitches
254
0
2 *)
A
- Counting tape cutter at the seam end
004
LS Light barrier compensating stitches
stitches
254
0
7 *)
A
005
Number of stitches of the light barrier filter for
stitches
254
0
1 *)
A
knitted
fabrics
006
Number of light barrier seams
15
1
1
A
007
Number of stitches for the seam with stitch
stitches
254
0
20
A
counting
009
LS Light barrier On/Off
ON/OFF
OFF *)
A
013
Thread trimmer On/Off
ON/OFF
ON *)
A
014
Thread wiper On/Off
ON/OFF
ON *)
A
015
Stitch counting On/Off
ON/OFF
OFF
A
018
OFF = Sequence “overlock mode with stop”
ON/OFF
OFF
A
ON = Sequence “overlock mode without auto-
matic stop.
019
0 = Pedal in pos. –1 blocked in the seam; with pedal in
4
0
3 *)
A
pos. –2 in the seam, only sewing foot lifting is
possible. (Function only if parameter 009 = ON)
1 = Pedal in pos. –1, sewing foot lifting blocked in the
seam.
2 = Pedal in pos. –2, thread trimming blocked.
(Function only if parameter 009 = ON)
3 = Pedal in pos. –1 and –2 active in the seam.
4 = Pedal in pos. –1 and –2 blocked in the seam.
(Function only if parameter 009 = ON)
020
kLM Clamp at the seam end On/Off
ON/OFF
OFF
A
021
ckL Run-out stitches clamp at the start of the seam stitches
254
0
2 *)
A
(Parameter 290 = 6 and 7)
022
OFF = Chain suction until the end of count c2 ON/OFF
OFF
A
ON = Chain suction at the seam end until
pedal in pos. 0 (neutral)
023
Automatic sewing foot lifting with pedal forward at the
1
0
1
A
seam end, if light barrier or stitch counting is switched on.
0 = Automatic sewing foot Off
1 = Automatic sewing foot On
024
Thread tension release with sewing foot lifting,
1
0
1
A
if parameter 290 = 13 and thread trimmer is switched off.
0 = Thread tension release with sewing foot only at the
seam
end
1= Thread tension release with sewing foot at inter-
mediate stop and at the seam end
026
Switchable stop for Pegasus backlatch machines
1
0
0
B
if parameter 290 = 8
0 = Stop in position 2 after the backlatch cycle and speed
n12
1 = Stop always in position 1
030
0 = Bobbin thread monitor Off
3
0
0
A
1 = Bobbin thread monitor with stop
2 = Bobbin thread monitor without stop
3 = Bobbin thread monitor with stop and start
blockage after thread trimming
031
Number of stitches for bobbin thread monitor
stitches 25500 ***)
0
0
A
*)
Depending on the selected mode. See table at the beginning of the List of Parameters!
***)
When programming the 5-digit (max) parameter values on the control, the 3-digit value displayed must be
multiplied by 100.
