Effekta AX M2 Series User Manual Download Page 35

Page: 35 / 132

Innovating power.

Control and display elements - Page 35

Solar inverter | V1.7

Automatic

restart with

overheating

Deactivate restart

(preset)

Activate restart

Set the output frequency

50Hz (preset)

60Hz

Operating logic

Automatic (preset)

When selected and utility

is availably, the inverter

operates in line mode. If

the mains frequency is

instable , the inverter

operates in bypass mode

when the bypass function

in program 23 is not

prohibited.

Online mode

When selected, the

inverter operates in

mains mode if mains

power is available.

ECO mode

When bypass in program

23 is selected and bypass

is not prohibited, the

inverter operates in ECO

mode if mains power is

available.

Summary of Contents for AX M2 Series





































































































































Search results

Summary of Contents for AX M2 Series

Reviews:

Related manuals for AX M2 Series

Brands by name

Popular brands

Effekta AX M2 Series, User Manual

Search results

Summary of Contents for AX M2 Series

Reviews:

Related manuals for AX M2 Series

Brands by name

Popular brands