manualshive.com logo in svg

Eelectron BO08A01KNX, Product Handbook

Share
Download
Eelectron BO08A01KNX Product Handbook Download Page 30

BO08A01KNXFI01010002.DOC 

 

 

 

Din Rail 8 Output Module– Product Handbook 

 

30/51 

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia 
+39 02.9316681  +39 02.93507688  
[email protected]  www.eelectron.com 

BO08A01KNXFI01010002.DOC 

C.F. e P.IVA 11666760159 
Capitale sociale: 800.000,00€ interamente versato 
Tribunale di Milano 359157-8760-07 
CCIAA Milano 148549 

When the scene function is enabled a communication object named 

<Output x> Scene

 becomes 

visible. 
 
It is possible to send to the device two possible commands:  

 

recall scene - is a command to create a specific condition  

 

store scene -  is a command to learn and store the current status (at the moment the 
command is received) of the contact, and then reproduce it once the recall command is 
received  

 
For every channel it is possible to store a maximum of 4 output scene. 
 

KNX PARAMETER 

SETTINGS 

Scene Number <X> 

 
0 … 64 

 

For the 4 possible scenes, this number is the unique identifier for the scene: valid numbers are 
from 0 to 63; 64 means scene is not active. 
 

Initial value Scene <X> 

 

 Contact Open 

  Contact Close  

 

For the 4 possible scene this number allow to initialize the status associated to previously 
selected scene number avoiding to execute the store scene procedure. If the store scene is done, 
this value is overwritten. 
 

Learn Scene 

 

 Enabled  

 Disabled  

 

This parameter enable / disable the output channel from storing value received from the bus; if 
this parameter is set to disable the value associated are set only by the parameters 

“Initial value 

Scene <X>” 

and cannot be modified without a ETS download. 

 
 

NOTES: 
 
[1]:

 When a scene is recalled the output channel behaves in the same way as it would have 

received a telegram “0” or “1” on the 

<Output x> Relay Command

 communication objects; this 

means that if a output is normally open with the staircase light timer enabled – the receipt of a 
telegram “1” triggers a timed ON with automatic OFF when the timer expires. 

 

[2]:

 After a ETS download the device assumes the value of parameter: “

Initial value Scene <X>” 

as a value in memory for the corresponding scene and overwrites previous memorized scene 
positions.

 

 
 
 

Summary of Contents for BO08A01KNX




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands