Edimax PS-1001 User Manual Download | Manualshive

Page: 57 / 90

background image

User's Manual

6.

UNIX System Network

6.1

Introduction

The PrintSir is available for TCP/IP printing by Unix lpd (Line

Printer Daemon) protocol. The lpd protocol originated with Unix release
is based on the BSD version of Unix and supported under most versions
of Unix.

This chapter explains how to c onfigure the PrintSir for TCP/IP

operation, and how to modify configuration files on your Unix system to
allow printing to the PrintSir. The configuration examples in this manual
follow the syntax for BSD based Unix systems. Please refer to the related
system documentation for the correct syntax of your systems.

To configure the PrintSir for lpd printing, perform the procedures

below:

1.

Enable PrintSir

’

s TCP/IP Support.

2.

Set up PrintSir

’

s IP address.

3.

Verify PrintSir

’

s IP Address.

4.

Configure remote lpd printing on the host.

5.

Print a test page.

In the next sections, we will describe these five procedures step by

step.

6.2

Enable PrintSir’s TCP/IP Support

The default configuration of the PrintSir is with TCP/IP support

enabled. Anyway, you can configure the PrintSir to enable TCP/IP support
using the configuration program or PSETUP program in the CD-ROM
included with the PrintSir.

«
...
55
56
57
58
59
...
»

Summary of Contents for PS-1001



























































































Reviews:

No comments

Related manuals for PS-1001

Pixma G1000 series

Brand: Canon Pages: 2

Pixma G1000 series

Brand: Canon Pages: 80

Brand: Canon Pages: 358

Brand: IBM Pages: 64

Brand: U.S. Converters Pages: 5

Brand: Avaya Pages: 19

Brand: Printronix Pages: 206

Brand: Synology Pages: 24

Brand: Panduit Pages: 59

SUPERSERVER 1028UX-CR-LL1

Brand: Supermicro Pages: 128

Brand: Sam4s Pages: 24

Brand: Xerox Pages: 2

EMBEDDED UNIT EU

Brand: Epson Pages: 28

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brand: Epson Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands