Edimax PS-1001 User Manual Download

Page: 72 / 90

User's Manual

IP Address

: specifies the IP address of PrintSir itself.

Starting IP

: specifies the starting IP address for assigning to

DHCP clients.

IP range

: specifies how many IP addresses are available to DHCP

clients.

Gateway IP

: gives the IP address of the default gateway.

Netmask

: gives the network mask.

DNS server

: gives the IP address of the domain name server.

The Write button

: save the configuration to the PrintSir.

The Reset button

: reset the PrintSir to let the changes take effect.

7.13

DHCP Information - DHCP Information

The DHCP Information page can be used to display the DHCP server

information when the PrintSir is with DHCP server function.

The status

: displays if the PrintSir acts as DHCP server or not.

Starting IP

: displays the starting IP address for assigning to

DHCP clients.

Summary of Contents for PS-1001



























































































Search results

Summary of Contents for PS-1001

Reviews:

Related manuals for PS-1001

Brands by name

Popular brands

Edimax PS-1001, User Manual

Search results

Summary of Contents for PS-1001

Reviews:

Related manuals for PS-1001

Brands by name

Popular brands