manualshive.com logo in svg

Edge-Core ES3510MA-DC, Management Manual, Page: 687 / 1098

Share
Download
Edge-Core ES3510MA-DC Management Manual Download Page 687

C

HAPTER

 25

  |  General Security Measures

ARP Inspection

–  687  –

E

XAMPLE

Console#show ip source-guard binding

MacAddress        IpAddress       Lease(sec) Type                 VLAN Interface

----------------- --------------- ---------- -------------------- ---- --------

11-22-33-44-55-66 192.168.0.99             0 Static                  1 Eth 1/5

Console#

ARP I

NSPECTION

ARP Inspection validates the MAC-to-IP address bindings in Address 

Resolution Protocol (ARP) packets. It protects against ARP traffic with 

invalid address bindings, which forms the basis for certain “man-in-the-

middle” attacks. This is accomplished by intercepting all ARP requests and 

responses and verifying each of these packets before the local ARP cache is 

updated or the packet is forwarded to the appropriate destination, 

dropping any invalid ARP packets.

ARP Inspection determines the validity of an ARP packet based on valid IP-

to-MAC address bindings stored in a trusted database – the DHCP snooping 

binding database. ARP Inspection can also validate ARP packets against 

user-configured ARP access control lists (ACLs) for hosts with statically 

configured IP addresses.

This section describes commands used to configure ARP Inspection. 

Table 83: ARP Inspection Commands  

Command

Function

Mode

ip arp inspection

Enables ARP Inspection globally on the switch

GC

ip arp inspection filter

Specifies an ARP ACL to apply to one or more VLANs GC

ip arp inspection log-buffer 

logs

Sets the maximum number of entries saved in a log 

message, and the rate at these messages are sent

GC

ip arp inspection validate

Specifies additional validation of address 

components in an ARP packet

GC

ip arp inspection vlan

Enables ARP Inspection for a specified VLAN or range 

of VLANs

GC

ip arp inspection limit

Sets a rate limit for the ARP packets received on a 

port

IC

ip arp inspection trust

Sets a port as trusted, and thus exempted from ARP 

Inspection

IC

show ip arp inspection 

configuration

Displays the global configuration settings for ARP 

Inspection

PE

show ip arp inspection 

interface

Shows the trust status and inspection rate limit for 

ports

PE

show ip arp inspection log

Shows information about entries stored in the log, 

including the associated VLAN, port, and address 

components

PE

Summary of Contents for ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments