manualshive.com logo in svg

Edge-Core ES3510MA-DC, Management Manual, Page: 330 / 1098

Share
Download
Edge-Core ES3510MA-DC Management Manual Download Page 330

C

HAPTER

 14

  |  Security Measures

ARP Inspection

–  330  –

◆

ARP Inspection ACLs can be applied to any configured VLAN.

◆

ARP Inspection uses the DHCP snooping bindings database for the list 

of valid IP-to-MAC address bindings. ARP ACLs take precedence over 

entries in the DHCP snooping bindings database. The switch first 

compares ARP packets to any specified ARP ACLs.

◆

If 

Static

 is specified, ARP packets are only validated against the 

selected ACL – packets are filtered according to any matching rules, 

packets not matching any rules are dropped, and the DHCP snooping 

bindings database check is bypassed.

◆

If 

Static

 is not specified, ARP packets are first validated against the 

selected ACL; if no ACL rules match the packets, then the DHCP 

snooping bindings database determines their validity.

P

ARAMETERS

These parameters are displayed:

◆

ARP Inspection VLAN ID

 – Selects any configured VLAN. (Default: 1)

◆

ARP Inspection VLAN Status

 – Enables ARP Inspection for the 

selected VLAN. (Default: Disabled)

◆

ARP Inspection ACL Name

■

ARP ACL

 – Allows selection of any configured ARP ACLs. 

(Default: None)

■

Static

 – When an ARP ACL is selected, and static mode also 

selected, the switch only performs ARP Inspection and bypasses 

validation against the DHCP Snooping Bindings database. When an 

ARP ACL is selected, but static mode is not selected, the switch first 

performs ARP Inspection and then validation against the DHCP 

Snooping Bindings database. (Default: Disabled)

W

EB

 I

NTERFACE

To configure VLAN settings for ARP Inspection: 

1.

Click Security, ARP Inspection.

2.

Select Configure VLAN from the Step list.

3.

Enable ARP inspection for the required VLANs, select an ARP ACL filter 
to check for configured addresses, and select the Static option to 

bypass checking the DHCP snooping bindings database if required.

4.

Click Apply. 

Summary of Contents for ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments