background image

8

BURNER SETUPS

SIDE WALL VENTED (FDVS)

SUGGESTED BECKETT BURNERS SETUPS

Note:

 

These settings are intended for initial start up only.  Final adjustments must be made using combustion test instruments.

Boiler 

Size

Firing 

Rate

Beckett 

Burner

Burner Part 

Number

Nozzle 

Mfg.

Nozzle Size

Pump 

Presure Head / Choke

Drawer 

Assy 

Adj

Low Fire 

Baffle

Air 

Shutter

Vent Kit Part 

Number 

Less Burner

Vent Kit Part 

Number with 

Burner

PFO-3

0.65

AFG

14619202 Delavan .60 X 80 A

140

F0

Fixed

Yes

125

550001447 550001450

0.75

AFG

14619202 Delavan .65 X 70 A

140

F0

Fixed

No

110

550001447 550001450

0.90

AFG

14619202 Delavan .75 X 80 B

140

F3

Fixed

No

55

550001447 550001450

PFO-3T

0.65

AFG

14619202 Delavan .60 X 80 A

140

F0

Fixed

Yes

125

550001447 550001450

0.85

AFG

14619202 Delavan .75 X 80 A

140

F3

Fixed

No

110

550001447 550001450

1.10

AFG

14619202 Delavan .90 X 80 B

140

F3

Fixed

No

55

550001447 550001450

PFO-4

0.65

AFG

14619202 Delavan .60 X 80 A

140

F0

Fixed

Yes

80

550001448 550001451

1.00

AFG

14619202 Delavan .75 X 80 A

140

F3

Fixed

No

45

550001448 550001451

1.35

AFG

14619202 Delavan 1.20 X 80 B

140

F6

Fixed

No

130

550001448 550001451

PFO-4T

0.65

AFG

14619202 Delavan .60 X 80 B

140

F0

Fixed

Yes

80

550001448 550001451

0.95

AFG

14619202 Delavan .85 X 80 B

140

F3

Fixed

No

45

550001448 550001451

1.45

AFG

14619202 Delavan 1.25 X 80 B

140

F6

Fixed

No

130

550001448 550001451

PFO-5

0.75

AFG

14619202 Delavan .65 X 80 A

140

F3

Fixed

Yes

75

550001448 550001451

1.10

AFG

14619202 Delavan 1.00 X 80 A

140

F6

Fixed

No

155

550001448 550001451

1.70

AFG

14619202 Delavan 1.50 X 80 A

140

F12

Fixed

No

222

550001448 550001451

PFO-5T

0.80

AFG

14619202 Delavan .65 X 70 A

140

F3

Fixed

Yes

75

550001448 550001451

1.50

AFG

14619202 Delavan 1.00 X 70 A

140

F6

                

No

155

550001448 550001451

1.75

AFG

14619202 Delavan 1.50 X 70 A

140

F12

Fixed

No

222

550001448 550001451

PFO-6T

0.95

AFG

14619202 Delavan .85 X 80 B

140

F3

Fixed

No

50

550001448 550001451

1.45

AFG

14619202 Delavan 1.20 X 80 B

140

F6

Fixed

No

110

550001448 550001451

2.10 CF375 240006433 Delavan 1.75 X 45 B

140

CF56KZ SL1

0

No

60

550001448 550001449

PFO-7

 

1.00

AFG

14619202 Delavan .90 X 80 B

140

F3

Fixed

No

100

550001448 550001451

1.60

AFG

14619202 Delavan 1.35 X 80 B

140

F12

Fixed

No

190

550001448 550001451

2.35 CF375 240006433 Delavan 2.00 x 45 B

140

CF56KZ SL1

0

No

170

550001448 550001449

PFO-8T

1.25

AFG

14619202 Delavan 1.00 X 70 A

140

F6

Fixed

No

70

550001448 550001451

1.90* CF375 240006433 Delavan 1.50 X 45 B

140

CF56KY V1

1

No

45

550001448 550001449

2.75 CF375 240006433 Delavan 2.25 X 45 B

140

CF56KZ SL1

1

No

140

550001448 550001449

PFO-9

1.35

AFG

14619202 Delavan 1.20 X 70 A

140

F6

Fixed

No

127

550001448 550001451

2.00 CF375 240006433 Delavan 1.65 X 45 B

140

CF56KZ SL1

0

No

55

550001448 550001449

3.00 CF375 240006433 Delavan 2.50 X 45 B

140

CF56KZ SL1

3

No

120

550001448 550001449

1. All burners fired at an over fire pressure of +0.02” w.c.

2. Burner insertion depth is 4 ⅝”

3. Nozzles are NOT factory installed and must be installed in the field.

4. All F Heads are fixed with a “Z” dimension of 1 ⅛”. See Beckett burner manual for proper “Z” dimension setup.

* NOTE: 

The burner for the 8 section FDVS 1.90 GPH input needs a static disk change, see the Kit #550001620 for details.

Summary of Contents for ULTIMATE PF Series













































Reviews: