Electro Industries Mini-Boiler BH309 Installation & Operating Instructions Manual Download

Page: 1 / 18

08/07/2008

BI301D

Electric

Mini-Boiler

Installation & Operating

Instructions

Model EMB-5

4.5 kW

3 GPM (11.35 L/min) minimum flow

Model EMB-9

9 kW

4 GPM (15.14 L/min) minimum flow

Application

- Low temperature, low pressure, radiant underfloor heating systems.

Comment

- If this application is for traditional hydronics heating requiring temperatures greater

than 140

F (60° C) and capacities larger than shown above, contact factory for other Electro-

Boiler product series.

Accessories –

Attached BL001 lists various accessory or option items which are not part of basic

Electro-Boiler. Page 1 gives information on a zone control update which stages elements based
upon zone capacity.

Note:

This product meets the requirements of the ASME Boiler and Pressure

Vessel Code.

Drawings:

BX301

BH302
BS302
BL001

Summary of Contents for Mini-Boiler BH309



















Search results

Summary of Contents for Mini-Boiler BH309

Reviews:

Related manuals for Mini-Boiler BH309

Brands by name

Popular brands

Electro Industries Mini-Boiler BH309, Installation & Operating Instructions Manual

Search results

Summary of Contents for Mini-Boiler BH309

Reviews:

Related manuals for Mini-Boiler BH309

Brands by name

Popular brands