EchoStar Hughes 9502 ATEX User Manual Download Page 65 | Manualshive

Page: 65 / 75

background image

Chapter 5

•

Lightning protection and safety

3500782-0001 Revision E

65

Chapter

5

Lightning protection and safety

Lightning and grounding precautions /

La foudre et la terre

précautions

A lightning strike on the ODU, mounting hardware or cable may cause death or
serious injury and is likely to damage both the ODU and the IDU.

La foudre sur l'ODU, le matériel de montage ou les câbles peut causer des blessures
graves ou mortelles et est susce

ptible d'endommager à la fois l'ODU et l’IDU.

It is therefore essential that the installer does not use an installation location, which
is likely to experience a lightning strike, and make suitable grounding and lightning
protection arrangements to minimize any possibility of injury or damage.
Professional local advice should be sought with respect to these matters. Hughes
accepts no liability for any injury or damage caused by lightning strikes.

Il est donc essentiel que l'installateur évite tout emplacement d'installation

susceptible d’être frappé par la foudre, et de mettre en place un dispositif de mise à

la terre et de protection contre la foudre adapté afin de minimiser tout risque de
blessure ou de dommage. Un conseil professionnel local devrait être consulté à cet
égard. Hughes n'accepte aucune responsabilité pour tout préjudice ou dommage
causé par la foudre.

Hughes 9502 indoor unit (IDU) chassis shall be connected to earth ground. Connect
the earth grounding wire with lug in between the ground screw and chassis. Tighten
the ground screw after the wire lug is installed. The wire lug material shall be either
tin-plated copper or tin-plated steel.

Le châssis de l’unité d’intérieur Hughes 9502 (IDU) doit être connecté à la terre.

Connectez le câble de mise à la terre avec une cosse entre la vis de terre et le châssis.
Serrez la vis de terre après que le câble avec cosse ait été installé. Le câble avec
cosse doit être soit en cuivre zingué ou en acier étamé.

Hughes also recommends that a protective earth cable be connected to the ODU or
ODU mount. Please consult professional local advice for protective earth grounding
requirements.

Hughes recommande ég

alement qu’un câble de terre de protection soit connecté à

l'ODU ou au montage de l’ODU. Veuillez consulter un conseil professionnel local pour

les spécificités concernant la mise à la terre de protection.

«
...
63
64
65
66
67
...
»

Summary of Contents for Hughes 9502 ATEX












































































Reviews:

No comments

Related manuals for Hughes 9502 ATEX

Brand: Eartec Pages: 2

Brand: Skytec Pages: 12

Brand: Optimus Pages: 44

Brand: Shimano Pages: 1

Brand: VocoPro Pages: 26

Brand: Prodipe Pages: 24

MICPRO UHF-5100

Brand: UMT Pages: 4

Brand: Roadstar Pages: 45

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 18

Brand: Polaris Pages: 8

Brand: Garmin Pages: 2

Brand: Cisco Pages: 32

Brand: Cisco Pages: 64

Brand: Silvercrest Pages: 24

Brand: Silvercrest Pages: 35

Brand: Silvercrest Pages: 42

Brand: Silvercrest Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands