EchoStar Hughes 9502 ATEX User Manual Download Page 49 | Manualshive

Page: 49 / 75

background image

Chapter 4

•

Installation instructions

3500782-0001 Revision E

49

ODU installation using the basic fix mount kit;

(P/N 3004066-0002)

You may install the fixed mount on any structurally sound surface; either on a
horizontal, or vertical, or a sloped surface such as a roof or wall.

1.

The pole has a 1.66” (4.2164cm) outer diameter (schedule 40 metal).

2.

The pole mount is 2lbs/0.9Kg. The azimuth/elevation bracket is 1 lb/0.45Kg.

3.

The wall mounting pattern has four bolts in a 6” x 3 ¾” (15.24cm x 9.525cm)

rectangle

(not included). The holes are 0.325” diameter. See

Figure 27: Base bracket hole pattern

«
...
47
48
49
50
51
...
»

Summary of Contents for Hughes 9502 ATEX












































































Reviews:

No comments

Related manuals for Hughes 9502 ATEX

Brand: ZF Pages: 28

Brand: Samsung Pages: 2

Brand: Panasonic Pages: 16

Brand: ascon Pages: 8

Soundgear Series

Brand: JBL Pages: 73

Brand: Teac Pages: 60

Brand: AKG Pages: 49

Brand: MXL Pages: 6

Brand: GLEMM Pages: 16

Brand: JTS Pages: 13

Brand: Landscape Vibrations Pages: 8

CMT-BX1 Marketing

Brand: Sony Pages: 2

Brand: ADLINK Technology Pages: 84

Brand: Polk Audio Pages: 4

Brand: MXL Pages: 2

Brand: Curtis Pages: 1

Brand: Curtis Pages: 7

Brand: Void Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands