EchoStar Hughes 9502 ATEX User Manual Download Page 15

Page: 15 / 75

Chapter 1

•

Product description

3500782-0001 Revision E

Optional mounting accessories

The IDU can be mounted using the IDU strap (P/N 3500617-0001) if desired. Strap
will require 4 each mounting

bolts either M3.5 or 6/32” (not included).

Figure 5: IDU mounting strap

The ODU can be mounted using the Basic Fixed Mount Kit (P/N 3004066-0002) or by
using the azimuth elevation bracket (P/N 1022994-0022) and an existing

1.5”

diameter pole.

Figure 6: Azimuth/elevation bracket

Main features of the 9502

The main features of the Hughes 9502 terminal are listed below:

•

Use of Internet Protocol (IP) via the BGAN satellite network

•

Remote Management

—

Web UI interface

—

SMS Control

—

AT Command Control

—

Log file upload

—

Terminal configuration

—

Remote firmware upgrade

•

Power Savings and Sleep Mode

•

IP Watchdog

•

Install Mode

•

XL-band ready

•

NAT, NAPT, Relay and PPPoE Modes

•

Auto Power ON when power is applied

Summary of Contents for Hughes 9502 ATEX












































































Search results

Summary of Contents for Hughes 9502 ATEX

Reviews:

Related manuals for Hughes 9502 ATEX

Brands by name

Popular brands

EchoStar Hughes 9502 ATEX, User Manual

Search results

Summary of Contents for Hughes 9502 ATEX

Reviews:

Related manuals for Hughes 9502 ATEX

Brands by name

Popular brands