EchoStar Hughes 4510 User Manual Download Page 40

Page: 40 / 47

Chapter 3 • Using the Web UI

H65874 Revision C

Acronym/Term

Definition

RRCHP Status

Status of RRC idle procedure

System ID

System identifier

Receive Statistics

ARFCN

Absolute Radio Frequency Channel Number

Burst MCS

Burst Modulation and Coding Scheme

Burst Type

Physical layer internal burst type

Frame

Physical layer internal frame number

Freq. Offset

Received burst frequency offset

RSSI

Received burst RSSI

Slot

Physical layer internal slot number

SQI

Received burst SQI

Status Flag

Physical layer status flag

Time Offset

Received burst time offset

Transmit Statistics

ARFCN

Absolute Radio Frequency Channel Number

Burst MCS

Burst Modulation and Coding Scheme

Burst Type

Physical layer internal burst type

Frame

Physical layer internal frame number

PAN

Power Attenuation Notification

PD CW

Physical layer internal Power Detector Code Word

Slot

Physical layer internal slot number

VGA CW

Physical layer internal VGA Code Word

3.6.5

Update Software

This subpage provides a convenient method to upgrade the terminal software. Before beginning the

process, please make sure to obtain the latest terminal software package. This package can be found
under the file name of

em_4510_5.x.x.x.hif

, where

x.x.x

correspond to the software release

number. The EM terminal software package contains all necessary images for the Hughes 4510
product. The terminal automatically detects the software images, which apply to the product after

loading the software package into the terminal.

It is not recommended to downgrade the terminal software to an older
release. Doing so will automatically reset all configuration settings to their

factory default settings and delete all user data stored on the terminal.

To upgrade the terminal software, follow these steps:

Store the terminal software package on the local drive of a computer attached to the

terminal.

Click the

Browse

button.

Navigate to the storage location of the software package, select the file, and click

Open

Click the

Start Update

button:

Summary of Contents for Hughes 4510
















































Search results

Summary of Contents for Hughes 4510

Reviews:

Related manuals for Hughes 4510

Brands by name

Popular brands

EchoStar Hughes 4510, User Manual

Search results

Summary of Contents for Hughes 4510

Reviews:

Related manuals for Hughes 4510

Brands by name

Popular brands