EBS-6200
Printer User's Manual
Chapter 4 - Operating the Printer
62
20091020#1.0
4.4.4.2. Sucking
In the main MEN
and then the
CLEAN NOZZLE
item.
zzle by sucking out ink from the nozzle and the gun (for about
o its previous condition. The green lamp indicator
V1
on the
external panel emits light during the operation. The
CLEAN NOZZLE
command should be used, if the
in et fails
gutte
the o
f
c
m
i
TE:
The comman is not e
After th
and ha
o the
restart
mode for about
1 minute.
Ink/Solvent
U select the
SERVICE
item
This command is used to clear the no
2 seconds). Then the system returns t
k j
to reach the
r after the ink flow has been turned on or if the nozzle has clogged during
low has been stopped intentionally with the
INK OFF
or
FAST OFF
gnored.
xecuted during printing.
s been executed, the printer switches t
peration. If the ink
and, the command is
om
NO
•
•
d
e comm
4 4
The
V
used
out o
refore any impurities gathered on the ink filter or in the nozzle
are not pulled back.
and opened in two parallel and independent ways:
d via the terminal,
•
With
the
comm
cuted
wher
osit
close
a te
In e main M
lect the
Closing th
Select the
V0 OFF
option and confirm the selection or press the
INK ON/OFF
key on the main
pad of the external panel. After the command has been executed, the
V0
valve is closed and the
green lamp indicator
V0
on the internal panel goes out.
If the ink flow is stopped, the following warning message is displayed:
IN 15 MIN. THE INK STREAM
HAS TO BE ON !!!!
The objective is to warn the printer operator that the
been closed. If the
V0
valve
remains closed for too long, the gun may dry up and the nozzle get clogged or even the entire ink
dry up. If the ink flow is not turned on during the indicated period, an alert signal is
nd another warning message is displayed:
OPEN V
PRIN
W
O
The wa
age c
the prin
s off a
!
.4. .3. Closing and Opening Ink Valve
0
valve opens/closes the ink flow towards the head. The valve open and close commands are
to clear the nozzle or ink filter inside the gun. The commands do not cause the ink to be sucked
f the nozzle and the gun and the
The ink valve can be closed
•
With commands entere
INK ON/OFF
ands are exe
key on the main pad of the external panel (the
V0 OFF
and
V0 ON
consecutively as the key is pressed). The key can be used regardless of
ion within the whole control menu is (for example, the valve can be
xt file is being edited).
SERVICE
item.
e the cursor p
d/opened while
th
ENU se
e V0 Valve
V0
valve has
system may
generated a
0 OR THE
TER
FF IN 1 MIN !!!
an be cleared only by opening the
V0
valve. If this message is ignored,
utomatically and
ILL BE SWITCHED
rning mess
ter switche
the head is not rinsed.
Opening
Select th
option and confirm the selection or press the
INK ON/OFF
key on the main pad
of the external panel. After the command has been executed the
V0
valve opens, and the green
The
V
comm
the V0 valve
e
V0 ON
lamp indicator
V0
on the internal panel comes on.
0 ON
command is used exclusively for service purposes, and it follows the
V0 OFF
and.
Summary of Contents for EBS-6200
Page 1: ...EBS 6200 USER S MANUAL Ink Jet technology for the future...
Page 2: ......
