background image

6

Installation

InstructIon manual

   MN050011EN   August 2022   www.eaton.com

Connecting the power supply

 

DANGER

IN SAFETY-RELEVANT APPLICATIONS, THE POWER SUPPLY  

USED TO POWER THE XN300 SYSTEM MUST BE A PELV POWER 

SUPPLY UNIT.

The two 24 V V+ terminals are internally connected to  

each other (X6: 

a

 and 

b

), as are the two 0 V GND terminals 

(X6: 

c

 and 

d

). Only one V+ and one 0 V terminal need to 

be connected in order to power the gateway. The internally 

connected terminals can be used to extend the 24 V and  

0 V supply voltage connections. However, it is necessary  

to make sure that a total current of 4 A is not exceeded  

per terminal.
External 24 Vdc voltages can also be distributed  

using an XN-322-4PS-20 power distribution module or  

XN-322-18PD-P and XN-322-18PD-M field potential 

distributor modules.
The plug connector with push-in spring-cage terminal  

FMC 1.5/4-ST-3.5 is included in the scope of supply.

Figure 11 .  Connection of power supply

24 V V+

24 V V+

0 V GND

0 V GND

The device must be powered with a galvanically isolated 

power supply with a rated voltage of 24 Vdc. A UL

T

 249 

fuse (maximum 4 A) must be installed between the power 

supply and the device.

Figure 12 .  Wiring the power supply




0.12 inch (3.0 mm)

F1

X6

U

e

 = 24 Vdc

(18–30 Vdc SELV)
I

e

 

 0.2 A

V+

V+

0 V

0 V

0 V

24 Vdc

F1

F1 

 4 A

Summary of Contents for XN300

















Reviews: