background image

iv

 

XN300 switch XN-332-5ETH-UMS

InstructIon manual

   MN050011EN   August 2022   www.eaton.com

Safety information

The instructions in this manual are not intended as a 

substitute for proper training or adequate experience in the 

safe operation of the equipment described. Only competent 

technicians who are familiar with this equipment should 

install, operate, and service it.
A competent technician has these qualifications:

 

Is thoroughly familiar with these instructions

 

Is trained in industry-accepted high- and low-voltage safe 

operating practices and procedures

 

Is trained and authorized to energize, de-energize, clear, 

and ground power distribution equipment

 

Is trained in the care and use of protective equipment 

such as arc flash clothing, safety glasses, face shield, 

hard hat, rubber gloves, clampstick, hotstick, etc.

Following is important safety information. For safe 

installation and operation of this equipment, be sure  

to read and understand all cautions and warnings.

Hazard statement definitions

This manual may contain four types of hazard statements.

 

DANGER

INDICATES AN IMMINENTLY HAZARDOUS SITUATION WHICH, IF 

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

 WARNING

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF 

NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY.

 CAUTION

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF 

NOT AVOIDED, MAY RESULT IN MINOR OR MODERATE INJURY.

NOTICE

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF 

NOT AVOIDED, MAY RESULT IN EQUIPMENT DAMAGE ONLY.

Safety instructions

Following are general caution and warning statements that 

apply to this equipment. Additional statements, related to 

specific tasks and procedures, are located throughout the 

manual.

 

DANGER

HAZARDOUS VOLTAGE. CONTACT WITH HAZARDOUS VOLTAGE 

WILL CAUSE DEATH OR SEVERE PERSONAL INJURY. FOLLOW ALL 

LOCALLY APPROVED SAFETY PROCEDURES WHEN WORKING 

AROUND HIGH- AND LOW-VOLTAGE LINES AND EQUIPMENT.

 WARNING

BEFORE INSTALLING, OPERATING, MAINTAINING, OR TESTING 

THIS EQUIPMENT, CAREFULLY READ AND UNDERSTAND THE 

CONTENTS OF THIS MANUAL. IMPROPER OPERATION, HANDLING, 

OR MAINTENANCE CAN RESULT IN DEATH, SEVERE PERSONAL 

INJURY, AND EQUIPMENT DAMAGE.

 

 WARNING

THIS EQUIPMENT IS NOT INTENDED TO PROTECT HUMAN LIFE. 

FOLLOW ALL LOCALLY APPROVED PROCEDURES AND SAFETY 

PRACTICES WHEN INSTALLING OR OPERATING THIS EQUIPMENT. 

FAILURE TO COMPLY CAN RESULT IN DEATH, SEVERE PERSONAL 

INJURY, AND EQUIPMENT DAMAGE.

 

 WARNING

POWER DISTRIBUTION AND TRANSMISSION EQUIPMENT MUST 

BE PROPERLY SELECTED FOR THE INTENDED APPLICATION. IT 

MUST BE INSTALLED AND SERVICED BY COMPETENT PERSONNEL 

WHO HAVE BEEN TRAINED AND UNDERSTAND PROPER SAFETY 

PROCEDURES. THESE INSTRUCTIONS ARE WRITTEN FOR SUCH 

PERSONNEL AND ARE NOT A SUBSTITUTE FOR ADEQUATE 

TRAINING AND EXPERIENCE IN SAFETY PROCEDURES. FAILURE TO 

PROPERLY SELECT, INSTALL, OR MAINTAIN POWER DISTRIBUTION 

AND TRANSMISSION EQUIPMENT CAN RESULT IN DEATH, SEVERE 

PERSONAL INJURY, AND EQUIPMENT DAMAGE.

 

 WARNING

OVERLAPPING ZONES OF PROTECTION ARE REQUIRED. UPSTREAM 

PROTECTION DEVICE SETTINGS MUST PROVIDE ADEQUATE 

OVERCURRENT PROTECTION IN THE EVENT OF A SYSTEM OR 

PRODUCT FAILURE. FAILURE TO PROPERLY SELECT APPROPRIATE 

UPSTREAM COORDINATION PROTECTION CAN RESULT IN DEATH, 

SERIOUS INJURY, AND EQUIPMENT DAMAGE.

This manual contains important information regarding the 

operation and installation of the Active Voltage Conditioner. 

All operations on the Active Voltage Conditioner should be 

carried out by a trained technician familiar with the contents 

of this manual.

Summary of Contents for XN300

















Reviews: