Eaton VORAD AlwaysAlert Installation Manual Download Page 1

Page: 1 / 30

Visit our website www.VORAD.com for additional information.

Or call 866-RV-VORAD (866-788-6723)

Eaton

VORAD

AlwaysAlert

™

Eaton

VORAD

SmartCruise

™

Eaton

VORAD

BlindSpotter

™

Installation Guide VOIG-0035 July 2005

A highly sophisticated radar-based system

that helps prevent front and side collisions.

Provides additional driver safety and

convenience with automated

cruise control.

AlwaysAlert

Helps Avoid Accidents

SmartCruise

Reduces Driver Fatigue

BlindSpotter

- "Sees" what you can't.

Reduces lane change/merge collisions.

Warns driver of obstacles in their blind spot.

Driver had constant visual alert when an object

is detected in the blind spot.

Audible and visual alerts activated with turn signal.

Significantly reduces rear-end collisions.

Helps drivers maintain safe following distances.

Audible/visual alerts to dangerous

obstacles ahead in rain, snow, fog

and night conditions.

Continuous undistracted road monitoring

up to 500-feet ahead and around curves.

Uses radar to automatically maintain a safe

cruise control following distance.

Electronically communicates with diesel engines

to match following speed with traffic flow.

Automatically engages the engine retarder when

engine braking is required to maintain safe

following distances.

Automatically returns to cruise set speed when

traffic clears.

VORAD = Vehicle Onboard RADar

Summary of Contents for VORAD AlwaysAlert































Search results

Summary of Contents for VORAD AlwaysAlert

Reviews:

Related manuals for VORAD AlwaysAlert

Brands by name

Popular brands

Eaton VORAD AlwaysAlert, Installation Manual

Search results

Summary of Contents for VORAD AlwaysAlert

Reviews:

Related manuals for VORAD AlwaysAlert

Brands by name

Popular brands