background image

21

Sonix 2Mx Technical Manual

SONIX 2MX TECHNICAL MANUAL  

TM370 / A  June 2022  www.eaton.com

8  Available features

8.1  Background Music

Background music is available as an additional feature of 

Sonix PA/GA system. It is not designed to be a complete 

fully flexible offering but can satisfy basic requirements.

To enable BGM the following steps need to be taken:

• 

Zoning is currently fixed within 2Mx firmware 

(customisable on request)

• 

Enable BGM in 2Mx configuration

• 

Disable Local attenuate on Hmi-26 access panels

• 

Apply audio to Sonix Io Aux input from a suitable 

source

• 

Enable Sonix Io Aux keyline, suggestion would be a 

key-switch to disable the feature as needed

• 

Toggle BGM on and off using local attenuate key on 

Hmi-26 

8.2  Fault monitoring

The Sonix system has been designed to monitor itself 

for faults and report any issues in a timely manner.

The pathways that available for monitoring are as 

follows:

• 

Data monitoring per Bus (Amp, Hmi #1, Hmi #2, Io, 

Beacon, Sync, Power and Global)

• 

Audio monitoring per Bus (Amp, Hmi #1, Hmi #2, Io, 

Sync and Global)

• 

Missing unit per Bus (excluding global bus)

• 

Connected equipment fault (excluding global bus)

• 

Duplicate unit (indication of bad/missing configuration)

• 

Internal Alarm tone generator 

8.2.1  Critical faults

Certain faults have been flagged as critical. These faults 

could adversely affect a systems ability to perform its 

primary function as a PA/GA system.

• 

Amplifier Line fault: 

Indicates an issue with the 

loudspeaker loops

• 

Beacon Line fault: 

Indicates an issue with the 

visual indicator warning loops

• 

Hmi duplicate priority fault: 

Misconfiguration of 

the Sonix access panel priority, prevents broadcasts 

etc.

8.2.2  Fault reporting

Any faults detected on the system are reported in 3 

ways by the unit:

• 

Activation of global fault signal via the Io

• 

Visual indication of fault source and type on 2Mx front 

panel

• 

Fault flags sent to the Sonix Administration Software 

(See SAS manual for details) 

8.2.3  Amplifier faults

In a typical PA/GA system, amplifiers are the most 

numerous items. To aid with issue tracking the extended 

2Mx Sync status report into SAS includes a slowly 

rotating list of any amplifiers currently in fault, including 

missing units (see SAS manual for details).

8.3  Alarm tones

The Sonix 2Mx generates the alarm tones for the 

system to broadcast. There are a possible 16 tones to 

choose from and the standard pre-loaded alarm tones 

available are as follows:

Tone

Name

Description

1

500 Hz

Solid 500 Hz

2

1 kHz

Solid 1 kHz

3

2 kHz

Solid 2 kHz

4

4 kHz

Solid 4 kHz*

5

Ramp down

1200 -> 500 Hz over 1 seconds

6

Ramp up

500 -> 1200 Hz over 1 seconds

7

1s Interrupted

1 kHz 1.0 second ON / 1.0 second OFF

8

0.5s Interrupted

1 kHz 0.5 second ON / 0.5 second OFF

9

Pulsed

1 kHz 5off 0.1 second ON / 0.1 second OFF, 1.0 

second OFF

10

IMO GA

1 kHz 7off 1.0 second ON / 1.0 second OFF, 7.0 

second ON / 1.0 second OFF

11

Ramp

500 -> 1200 -> 500 Hz over 3 seconds

12

0.1s Interrupted

1 kHz 0.1 second ON / 0.1 second OFF

13

1400 Hz

Solid 1400 Hz

14

Dual tone

800 Hz / 1 kHz changeover every 250 ms

15

550 Hz

550 Hz 0.1 second ON / 0.1 second OFF

16

440 Hz

440 Hz 0.4 second ON / 0.4 second OFF

Table 18 - Standard Alarm tones

ote: 

N

The alarm tones listed are standard, customization is available on 

request (see 9.2 Alarm Tones), customised alarm tones are not neces-

sarily reflected in SAS. 

ote: 

N

* Higher frequency alarm tones will have reduced dB SPL sound 

output.

8.4  Alarm Attenuate

Alarm Attenuate feature is used, by system operators, to 

reduce the volume of an active alarm. Within Sonix PA/

GA systems the level of attenuation is defined within the 

2Mx configuration. 

The level of attenuation is variable from 0 (limited 

attenuation, approximately -12dB) to 255 (maximum 

approximately -60dB, potentially inaudible)

There is an automatic timeout feature that will cancel 

alarm attenuate after 10/20/30 minutes or can be 

disabled.

ote: 

N

Eaton recommend an Alarm Attenuate setting of 120 with a mini-

mum value of 30 and a maximum value of 245

See SAS manual for more information.

Summary of Contents for SONIX 2Mx



























Reviews: