Eaton PowerXL DX-NET-ETHERCAT-2 Manual Download Page 5

Page: 5 / 56

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

Table of contents

About this Manual .....................................................................

0.1

Target group.................................................................................

0.2

Writing conventions .....................................................................

0.2.1

Hazard warnings of material damages .........................................

0.2.2

Hazard warnings of personal injury ..............................................

0.2.3

Tips...............................................................................................

0.3

Abbreviations and Symbols..........................................................

0.4

Units of measurement .................................................................

Device series...............................................................................

1.1

Checking the Delivery ..................................................................

1.2

Key to part numbers.....................................................................

1.3

General rated operational data .....................................................

1.4

Features .......................................................................................

1.5

Designation at DX-NET-ETHERCAT-2 .......................................... 10

1.6

Proper use.................................................................................... 11

1.7

Maintenance and inspection ........................................................ 12

1.8

Storage......................................................................................... 12

1.9

Service and warranty.................................................................... 12

1.10

Disposal........................................................................................ 12

Engineering................................................................................. 13

2.1

EtherCAT...................................................................................... 13

2.2

LED indicators .............................................................................. 14

2.2.1

LED status display........................................................................ 14

2.2.2

RUN LED...................................................................................... 14

2.2.3

LED ERR ...................................................................................... 14

2.2.4

LEDs Link/Activity ........................................................................ 15

Installation .................................................................................. 17

3.1

Introduction .................................................................................. 17

3.2

Notes on the documentation ....................................................... 18

3.3

Notes on the mechanical surface mounting ................................ 18

3.4

Mounting for frame sizes FS2 and FS3........................................ 19

3.5

Mounting from construction size FS4 .......................................... 20

3.6

Installing the fieldbus connection................................................. 22

3.7

Install field bus ............................................................................. 23

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

























































Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands

Eaton PowerXL DX-NET-ETHERCAT-2, Manual

Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands