Eaton PowerXL DX-NET-ETHERCAT-2 Manual Download Page 34

Page: 34 / 56

4 Commissioning

4.8 Mode parameter

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

4.8 Mode parameter

The abbreviations used in the parameter lists below have the following
meaning:

Figure 18:How the parameters are shown in the manual and in the software

The Baud rate will automatically be set to match the master.

PNU

Parameter number

Identification number of the parameter

RUN

Access rights to the parameters during operation (RUN):
/ = Modification permissible
- = Modification only possible in STOP

ro | rw

Parameter read and write permissions via a fieldbus connection:
ro = read only
rw = read and write (read and write)

Value

Setting of the parameter

Default setting: (P1.1 = 1) base parameter

￫

Access rights are not shown in the drivesConnect PC software.

Manual

PNU

Access right

Value

Description

RUN

ro | rw

①

②

③

④

PC Software

PNU

Description

Value

Range

Default

Visible

①

③

②

④

PNU

Access right

Designation

Value range

Value that must
be configured

RUN

ro | rw

P1-12

112

–

Control level

0 = Control signal terminals (I/O)
1 = Keypad (KEYPAD FWD)
2 = Keypad (KEYPAD FWD/REV)
3 = PID control
4 = field bus system (PROFINET-2, Modbus RTU, etc.)
5 = Slave mode
6 = field bus CANopen

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

























































Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands

Eaton PowerXL DX-NET-ETHERCAT-2, Manual

Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands