Eaton PowerXL DX-NET-ETHERCAT-2 Manual Download Page 11 | Manualshive

Page: 11 / 56

background image

1 Device series

1.1 Checking the Delivery

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

7

1 Device series

1.1 Checking the Delivery

Your fieldbus connection was carefully packaged and handed over for ship-
ment. The devices should be shipped only in their original packaging with
suitable transportation materials. Please observe the labels and instructions
on the packaging and for handling the unpacked device.

▶

Open the packaging with adequate tools and inspect the contents imme-
diately after receipt in order to ensure that they are complete and
undamaged.

The packaging must contain the following parts:

•

A fieldbus connection DX-NET-ETHERCAT-2,

•

the instruction leaflet IL040004ZU.

Figure 1:

Equipment supplied with fieldbus connection DX-NET-ETHERCAT-2

￫

Before opening the package, please check the nameplate on it
to make sure that you received the correct connection.

RUN

ERR

EtherCAT

«
...
9
10
11
12
13
...
»

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

























































Reviews:

No comments

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brand: Hainbuch Pages: 68

Brand: Icidu Pages: 34

Brand: Icom Pages: 2

Brand: Radicom Research Pages: 9

Brand: Yeastar Technology Pages: 52

Brand: Telex Pages: 6

USB External Sound Card Adapter

Brand: StarTech.com Pages: 9

Brand: Radio Shack Pages: 36

Brand: Oakton Pages: 9

eSecu FIDO2 Pro+ Fingerprint Key

Brand: Excelsecu Data Technology Pages: 29

SANblade QLA 2462

Brand: Qlogic Pages: 2

Brand: Orion Pages: 6

Brand: VOLTCRAFT Pages: 2

Brand: WiT Pages: 11

Brand: ISY Pages: 20

Brand: Brainboxes Pages: 10

Brand: Grandstream Networks Pages: 4

Brand: Grandstream Networks Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands