Eaton PowerXL DX-NET-ETHERCAT-2 Manual Download Page 15 | Manualshive

Page: 15 / 56

background image

1 Device series

1.6 Proper use

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

11

1.6 Proper use

The DX-NET-ETHERCAT-2 fieldbus connection is an electrical piece of equip-
ment that can be used to control DA1 variable frequency drives and connect
them to a standard EtherCAT field bus system. It is intended to be installed
in a machine or assembled with other components into a machine or system.
It makes it possible for DA1 series variable frequency drives to be integrated
as slaves into EtherCAT field bus systems.

Figure 4:

How the DX-NET-ETHERCAT-2 fieldbus connection
can be integrated into a EtherCAT network

a

Head-end controller (master)

b

EtherCAT cable

c

Variable frequency drive DA1 with DX-NET-ETHERCAT-2 connection

d

Motor(s)

The EtherCAT cable coming from the master needs to be plugged into the IN
RJ45 socket. The outgoing connection from the DX-NET-ETHERCAT-2
module needs to be connected using the OUT socket.

Simply leave the OUT socket on the last device (variable frequency drive)
alone. A bus termination resistor is not necessary.

￫

The DX-NET-ETHERCAT-2 fieldbus connection is not a house-
hold appliance, but rather a component intended exclusively for
use in commercial applications.

￫

Observe the technical data and connection requirements
described in this manual.
Any other usage constitutes improper use.

③

①

②

④

L1/L L2/N L3

DC-

U

DC+ BR

1 2 3 4 5 6 7 8 9 1

0 11 12 13

14 15 16 17 18

COM

V

W





L1/L L2/N L3

DC-

U

DC+ BR

1 2 3 4 5 6 7 8 9 1

0 11 12 13

14 15 16 17 18

COM

V

W





«
...
13
14
15
16
17
...
»

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

























































Reviews:

No comments

Related manuals for PowerXL DX-NET-ETHERCAT-2

D DPH-50U DPH-50U

Brand: D-Link Pages: 2

AirPlus DWL-810

Brand: D-Link Pages: 64

Brand: D-Link Pages: 39

Brand: D-Link Pages: 8

802.11g Wireless LAN USB Adapter DWL-G122

Brand: D-Link Pages: 43

AirPlusXtremeG DWL-G650

Brand: D-Link Pages: 20

Brand: fafnir Pages: 16

Allen-Bradley CrossBoard 141C-G Series

Brand: Rockwell Automation Pages: 4

Brand: Oehlbach Pages: 84

Brand: PATONA Pages: 14

Brand: GeoVision Pages: 3

Brand: Sense Pages: 4

Brand: ConvaTec Pages: 4

RTE7702012EAB00000J

Brand: Renesas Pages: 53

SANblade QLA 2462

Brand: Qlogic Pages: 2

Brand: Syba Pages: 2

ExpressSAS R30F

Brand: ATTO Technology Pages: 2

Brand: Radio Shack Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands