Eaton PowerXL DX-NET-ETHERCAT-2 Manual Download Page 18

Page: 18 / 56

2 Engineering

2.2 LED indicators

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

2.2 LED indicators

The module‘s LED indicators are used to indicate operating and network sta-
tuses, making quick diagnostics possible.

figure 5:

RUN, ERR, and Link/Activity (Port 1, Port 2) LED indicators

2.2.1 LED status display

The following LED are included:

2.2.2 RUN LED

The RUN LED is used to indicate CoE communications statuses.

2.2.3 LED ERR

The ERR LED indicates the EtherCAT communications error status.

EtherCAT

RUN

ERR

LED

Description

RUN LED

LED ERROR

Link/Activity (Port 1)

Link/Activity (Port 2)

LED status

Designation

Description

off

Init

no communication or power supply

Green illuminating

Operational

Communications have been fully established
(parameter transmission)

Green flashing

Pre-operational

Parameter communications have been established,
but process data communications have not

green single flash

Safe operational

Limited communications

Red flashing

Fatal Event

Fatal error

LED status

Designation

description

off

No Error

no error or device switched off

illuminated red

Application controller failure

EtherCAT status was exited (EXCEPTION)

Red flashing

Invalid Configuration

Configuration not OK

rot double flash

Application watchdog timeout

SyncManager Watchdog Time

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

























































Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands

Eaton PowerXL DX-NET-ETHERCAT-2, Manual

Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands