Eaton PowerXL DX-NET-ETHERCAT-2 Manual Download Page 13

Page: 13 / 56

1 Device series

1.3 General rated operational data

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

1.3 General rated operational data

1.4 Features

DX-NET-ETHERCAT-2 supports the following functions and specifications:

•

CANopen over EtherCAT (CoE),

•

plug-in connection RJ45

•

DS301 conformity,

•

isolated EtherCAT interface

•

Network ID changes

•

star and linear topology,

•

EMCY support,

•

Access to up to 16,383 ADIs, in the form of vendor-specific objects,
through the network,

•

Up to 256 I/O bytes in each direction (fast cyclic),

•

up to 127 slave cards,

•

device description file as xml-file.

Technical Data

Symbol

Unit

Value

General

Standards

meets the requirements of the EN 50178 (standard for electrical safety)

Production quality

RoHS, ISO 9001

Ambient conditions

Operation temperature

°C

-40 (no hoarfrost) up to +70

Storage temperature

°C

-40 - +85

Climatic proofing

< 95, relative humidity, no condensation permitted

Installation altitude

max. 1000

Vibration

m/s

5 – according to IEC 68-2-6;
10 – 500 Hz;
0.35 mm

EtherCAT connections

interface

RJ45 plug

data transfer

100 Mbit/s full-duplex

Transfer cable

Twisted two-pair balanced cable (screened)

Communication protocol

EtherCAT

IEEE 802.3 according to DS301 CANopen over EtherCAT

Baud rate

MBit/s

100

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

























































Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands

Eaton PowerXL DX-NET-ETHERCAT-2, Manual

Search results

Summary of Contents for PowerXL DX-NET-ETHERCAT-2

Reviews:

Related manuals for PowerXL DX-NET-ETHERCAT-2

Brands by name

Popular brands