C. M2-CEILING-SWIVEL-KIT
1.
S’assurer de couper l’alimentation au système de conduits avant d’installer le
luminaire.
2.
Identifier l’emplacement de montage approprié pour supporter le luminaire,
marquer et percer des trous pour les supports de fixation pivotants conformément
à l’entraxe « A » indiqué dans le tableau ci-dessous (voir figure 3).
3.
Monter les supports pivotants sur le boîtier du pilote du luminaire, comme illustré
à la figure 3. Utiliser deux (2) des boulons hexagonaux de 1/4 po et les rondelles
de blocage fendues fournies pour chaque support. Serrer à un couple de 64 po-lb
(7,2 N-m).
4.
Le luminaire est maintenant prêt à être installé. Il est fortement recommandé
de faire appel à deux (2) ouvriers qualifiés pour procéder au montage final
du luminaire. Il est recommandé d’éviter toute blessure personnelle ou tout
dommage au luminaire.
5.
Poser et serrer les fixations de 1/4 po de diamètre (fournies par le client) dans
chacun des trous de montage du support. Il est recommandé d’utiliser de la
quincaillerie en acier inoxydable dans les endroits présentant des problèmes de
corrosion.
6.
Régler la position du luminaire à l’angle désiré et serrer fermement les deux (2)
axes d’articulation de 5/16 po sur le support, puis serrer les écrous hexagonaux.
Serrer à un couple de 120 po-lb (13,6 N-m).
Lon-
gueur
2 pi (po)
2 pi
(mm)
4 pi (po)
4 pi
(mm)
A
26,4
670
26,4
670
B
24,0
610
39,0
991
Figure 3. Installation du support de plafond pivotant
THIRD ANGLE PROJECTION
166.9
6.57
175.3
6.90
A
B
B
669.3
26.35
1/4" SPLIT LOCK WASHER
1/4-20 x 1/2" CAP SCREW
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 3 OF 5
CODE ...
THIRD ANGLE PROJECTION
166.9
6.57
175.3
6.90
A
B
B
669.3
26.35
1/4" SPLIT LOCK WASHER
1/4-20 x 1/2" CAP SCREW
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 3 OF 5
CODE ...
D. M2-PM-KIT-*
1.
S’assurer de couper l’alimentation au système de conduits avant d’installer le
luminaire.
2.
Vérifier que le diamètre interne du collier est conforme au diamètre de la tige
avant l’installation. Les colliers sont disponibles dans les tailles 42 mm (1,65),
51 mm (2) et 60 mm (2,36) (voir la figure 5).
3.
Les supports de montage sur tige sont espacés de 20,75 po sur leurs axes
longitudinaux, comme illustrés à la figure 4.
4.
Serrer deux (2) des boulons hexagonaux de 1/4 po fournis et les rondelles de
blocage fendues sur chaque sous-ensemble de support. Serrer à un couple de
64 po-lb (7,2 N-m).
5.
Retirer les deux (2) vis de 5/16 po, les rondelles de blocage et les écrous de
chaque collier et retirer les moitiés supérieures des colliers.
6.
Le luminaire est maintenant prêt à être installé. Il est fortement recommandé
de faire appel à deux (2) ouvriers qualifiés pour procéder au montage final
du luminaire. Il est recommandé d’éviter toute blessure personnelle ou tout
dommage au luminaire.
7.
Positionner le luminaire de manière à ce que les moitiés inférieures des colliers
entourent la tige.
8.
Poser les deux (2) moitiés supérieures du collier, les vis de 5/16 po, les rondelles
de blocage et les écrous sur chaque collier.
9.
Serrer les écrous sur les vis de 5/16 po uniformément en suivant un ordre de va-
et-vient. Serrer à un couple de 120 po-lb (13,6 N-m).
No. de cat.
Configuration
Dimension (pouces)
A
B
C
D
M2-PM-KIT-1.25
Trousse PM 2.0 (taille
de 2 po)
4,331
3,543
2,36
1,693
M2-PM-KIT-1.5
Trousse PM 1.5 (taille de
1 – 1/2 po)
3,740
2,953
2,00
1,535
M2-PM-KIT-2.0
Trousse PM 1.25 (taille
de 1 – 1/14 po)
3,386
2,598
1,65
1,378
Lon-
gueur
2 pi (po)
2 pi
(mm)
4 pi (po)
4 pi
(mm)
A
24,0
610
39,0
991
B
Consulter le tableau ci-dessous pour connaître les
diamètres des colliers de serrage
Figure 4. Installation sur tige
Figure 5. Détails du montage sur tige
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
!
AVERTISSEMENT
Pour éviter toute blessure personnelle,
ne pas laisser pendre le luminaire sur un
seul support à la fois. Le non-respect de ces directives peut entraîner la rupture du
support et des blessures corporelles, voire la mort.
!
AVERTISSEMENT
Pour éviter toute blessure personnelle,
ne pas laisser pendre le luminaire sur un
seul support à la fois. Le non-respect de ces directives peut entraîner la rupture du
support et des blessures corporelles, voire la mort.
IF 1947 • 10/22 © Division Crouse-Hinds d’Eaton, 2022
Page 17
VIS DE MONTAGE 1/4-20 x 1/2 PO
RONDELLE DE BLOCAGE FENDUE 1/4 PO
[166,9]
6,57
B
[175,3]
6,90
[669,3]
26,35
B
[175,3]
6,90
[171]
6,7
[198]
7,8
B
[527,1]
20,75
A
A
A
B
C
D
A