EASTMAN 629XS Instruction Manual And Parts List Download Page 27

Page: 27 / 40

Form C-1572

Figure 22. Single Phase Motor Assembly (Exploded View)

Note:

L.H. indicates left-

hand thread. All others are
right-hand.

WARNING

Attach ground wire to ground terminal
“E” on Terminal block. Failure to
ground Terminal block may result in
electrocution or other serious
personal injuries.

STATOR WITH BAND
SINGLE-PHASE SINGLE-SPEED

(See Page 22 for Ratings)

514C8-110
514C8-113
514C8-124
514C8-127
514C8-137
514C8-138
514C8-140
514C8-141
514C8-201

CUTOUT

597C2-14

60Hz.

3600 R.P.M.

597C2-15

50Hz.

3000 R.P.M.

597C2-16

60Hz.

1800 R.P.M.

597C2-17

50Hz.

1500 R.P.M.

Attachment Plug

Terminal Block
See Back Cover

30C1-8

L.H.

10C1-41

4C2-87

L.H.

4C1-145

53C7-35

34C1-51

301C8-1

13C1-9

301C12-3

8C12-4

8C5-10

580C1-192

73C7-121

90C1-146

783C1-3

305C10-1

12C1-32

12C1-12

90C6-46

513C3-240

513C3-241

47C4-80

47C4-79

73C7-121

254C1

300C12-3

305C8-1

52C5-238

52C5-239

307C15-2

22C1-41

262C1-22

262C1-23

262C1-24

305C8-1

73C7-121

305C8-1

18C6-16

L.H.

580C1-212

580C1-213

236C1-177

79C2-82

79C2-84

Summary of Contents for 629XS









































Search results

Summary of Contents for 629XS

Reviews:

Related manuals for 629XS

Brands by name

Popular brands

EASTMAN 629XS, Instruction Manual And Parts List

Search results

Summary of Contents for 629XS

Reviews:

Related manuals for 629XS

Brands by name

Popular brands