manualshive.com logo in svg

EASTMAN 629XS, Instruction Manual And Parts List, Page: 28 / 40

Share
Download
EASTMAN 629XS Instruction Manual And Parts List Download Page 28

EASTMAN

Form C-1572

Three-Phase

Motor Assemblies

Figure 23.  Three-Phase Motor Assembly

(Assembled View)

Note:  

Please specify model and serial number

of machine when ordering parts.

Part No.

No. Req'd

Description

1C4-8

1

1

Sleeve, Cutout

4C1-145

1

1

Shaft Lock Nut

4C2-87

1

1

Nut, Clutch

10C1-41

1

1

Rotor Fan

12C1-12

1

1

Loading Spring Washer

12C1-32

1

1

Lock Washer

13C1-9

1

1

Turning Knob

18C6-16

1

1

Retaining Ring

20C13-94

2

2

Screw, M4 Pan Head

22C1-42

1

1

 Carrying Handle/Switch Body

30C1-8

1

1

Dust Cap

34C1-51

1

1

Clutch Spring

52C5-241

1

1

Switch Cover

52C5-242

2

2

Cover, Handle Side

53C7-35

1

1

Fan Cover

67C1-10

1

1

Cutout Mount

73C7-121

1

1

Tubing, Terminal Wire

79C2-81

1

1

Plate, Direction Arrow

79C2-82

1

0

Label, Safety Warning

79C2-84

0

1

Label, Safety Warning

90C1-146

1

1

Rear Bearing Housing

90C6-46

1

1

Rear Ball Bearing

199C1-23

3

3

Wire Lug

236C-177

1

1

Label, Warning

254C1

1

1

Cable Tie

300C12-3

4

4

Screw, 8-32 x 3/8 Round Hd.

300C10-8

2

2

Screw, #6-32 x 3/4 Round Hd.

301C8-1

3

3

Screw, #4-40 x 1/2 Fillister Hd.

305C8-1

14 14

Screw, #4-40 x 1/4 Binding Hd.

305C10-1

1

1

Screw, #6-32 x 1/4 Binding Hd.

307C15-2

2

2

Screw, #10-32 x 1/2 Button Head

513C3-240

1

0

Rotor  and Shaft

513C3-241

0

1

Rotor and Shaft

514C8-143

0

1

Stator with Band 220V 50 Hz. 3000 R.P.M.

514C8-146

0

1

Stator with Band 220V 60 Hz. 3600 R.P.M.

514C8-151

0

1

Stator with Band 380V 50 Hz. 3000 R.P.M.

514C8-152

0

1

Stator with Band 380V 50 Hz. 1500 R.P.M.

514C8-157

1

0

Stator with Band 220V 50Hz. 3000 R.P.M.

514C8-161

1

0

Stator with Band 380V 50 Hz. 3000 R.P.M.

580C1-98

1

1

Switch, 3 Phase

783C1-3

1

1

Ground Wire Assy.

CLASS 627

CLASS 629

24

Summary of Contents for 629XS









































Reviews:

No comments