EASTMAN 629XS Instruction Manual And Parts List Download Page 33

Page: 33 / 40

Form C-1572

Figure 27. Sharpener Housing Assembly (Exploded, Front View)

Note:

L.H. indicates left-hand thread.

All others are right-hand.

*THESE PARTS SOLD ONLY IN
ASSEMBLIES AS FOLLOWS.

713C4-4

Screw Shaft with Extension, R. & L. Hand Nuts 5"-8"

713C4-5

Screw Shaft with Extension, R. & L. Hand Nuts 9"-10"

713C4-6

Screw Shaft with Extension, R. & L. Hand Nuts 11 1/2"

713C4-7

Screw Shaft with Extension, R. & L. Hand Nuts 13"

732C1-11

5"-8" knife

732C1-12 9"-10" knife
732C1-20 11 1/2" knife
732C1-17

13" knife

For

Spacer

Chart

(See

Sharpener

Housing

Assembly

Drawing)

(Rear View)

Page 30

20C4-17

34C10-179

683C1-17

53C11-103

L.H.

5C5-16

17C15-106

147C1-26

12C15-57

20C12-156

621C1-7

309C15-7

97C3-35

34C10-107

20C12-113

55C4-49

20C12-13

34C1-20

11C12-54

90C4-47

4C1-149

86C7-34

71C3-15

*4C2-113

71C3-15

12C15-74

12C15-91

*4C2-112

22C3-2

300C10-1

605C1-36

5"-8" knife

605C1-37 9"-10" knife
605C1-33 11 1/2" knife
605C1-34

13" knife

553C1-11

12C15-130

300C10-4

34C8-12

171C1-16

553C1-12

692C2-15

118C1-8

300C10-4

62C16-334

17C5-18

302C10-11

302C10-8

307C15-1

53C11-181

68C1-192

20C12-117

Summary of Contents for 629XS









































Search results

Summary of Contents for 629XS

Reviews:

Related manuals for 629XS

Brands by name

Popular brands

EASTMAN 629XS, Instruction Manual And Parts List

Search results

Summary of Contents for 629XS

Reviews:

Related manuals for 629XS

Brands by name

Popular brands