EASTMAN 629XS Instruction Manual And Parts List Download Page 31

Page: 31 / 40

Form C-1572

Figure 25. Front Bearing Housing with Oiler Assembly (Exploded View)

Notes:

L.H. indicates left-hand thread. All others are right-hand.

Slip large lug over switch before replacing switch base. Secure switch to
base tightly to ensure positive ground.

Note:

Certain 220 volt machines will

use these capacitors. Please check
the capacitor number on label of your
machine to order.

706C1-4

110 Volt

706C1-5

220 Volt

706C1-13

110 Volt

706C1-18

220 Volt

664C1-6 1 1/8 Stroke
664C1-5 1 1/4 Stroke
664C1-4 1 1/2 Stroke
664C1-3 1 3/4 Stroke

525C1-4 1 3/4 Stroke
525C1-5 1 1/2 Stroke
525C1-6 1 1/4 Stroke
525C1-7 1 1/8 Stroke

85C1-52 1 1/8 Stroke
85C1-46 1 1/4 Stroke
85C1-45 1 1/2 Stroke
85C1-44 1 3/4 Stroke

18C6-79

141C1-46

18C6-80

52C5-240

305C8-1

300C12-6

308C12-1

4C3-8

300C3-2

53C6-2

191C1-42

191C1-43

302C8-2

73C7-204

191C1-45

222C1-7

201C1-11

73C7-203

607C1-35A
607C1-35B
607C1-35C
607C1-35D

90C2-165

72C4-28

62C1-140

307C18-1

4C1-111

18C5-9

20C12-79

8C9-22

531C1-92

531C1-90

34C10-142

4C2-110

660C4-14
660C4-15
660C4-16

53C11-180

308C12-1

305C8-1

53C11-183

20C12-62

4C2-91

309C15-5

12C10-2

302C10-4

71C3-18

90C6-38

15C13-23

15C13-34

15C13-39

11C12-92

90C6-46

4C1-190

4C1-132

579C2-17

12C15-14

308C14-1

12C1-21

12C15-53

91C4-25

24C1-3

12C1-24

17C4-6

54C4-32

63C5-11

191C1-21

191C1-38

20C5-17

Summary of Contents for 629XS









































Search results

Summary of Contents for 629XS

Reviews:

Related manuals for 629XS

Brands by name

Popular brands

EASTMAN 629XS, Instruction Manual And Parts List

Search results

Summary of Contents for 629XS

Reviews:

Related manuals for 629XS

Brands by name

Popular brands